Questions 7, 8 and 9: For the cantilever shown in the figure, If F₁ = 450 N, F₂-450 N, 8-30° and M-150 N.m determine: 7) The reaction at point O along x-axis, b) 390 N to the left d) 375 N to the right f) 225 N to the right a) Zero c) 390 N to the right e) 225 N to the left 0.2 m 9) The moment reaction about point 0, a) 1165 N.m counter-clockwise c) 990 N.m counter-clockwise e) 885 N.m counter-clockwise -1.5 m F₂ 8) The reaction at point O along y-axis, a) 225 N up b) 225 N, down c) 60 N, up d) 60 N, down c) 840 N, up b) 1165 N.m clockwise d) 990 N.m clockwise f) 885 N.m clockwise 2 m F₁ -1.5 m M f) 840 N, down

Questions 7, 8 and 9: For the cantilever shown in the figure, If F₁ = 450 N, F₂-450 N, 8-30° and M-150 N.m determine: 7) The reaction at point O along x-axis, b) 390 N to the left d) 375 N to the right f) 225 N to the right a) Zero c) 390 N to the right e) 225 N to the left 0.2 m 9) The moment reaction about point 0, a) 1165 N.m counter-clockwise c) 990 N.m counter-clockwise e) 885 N.m counter-clockwise -1.5 m F₂ 8) The reaction at point O along y-axis, a) 225 N up b) 225 N, down c) 60 N, up d) 60 N, down c) 840 N, up b) 1165 N.m clockwise d) 990 N.m clockwise f) 885 N.m clockwise 2 m F₁ -1.5 m M f) 840 N, down

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Graph about the imagen
Hi second question please. This is an engineering statics problem.
Laplace transformation
Show full detailed solution please.The units are in mm;1 rpm=0.104719755 rad/s
MA Figure (2) 3- The time response of a liner spring-mass-damper system with the mass of (m), the stiffness coefficient of (k), and a dampirg constant of (c) is given below in figure (2) with a set of coordinates marked by fillec circles. x(t) is in meters, it is in seconds. Indicate the units of all quantities involved in your solutions when calculate 0 -1- (0.53, 1.78) (0,0.8) 2 (2.1,-1.3) (3.7,0.9) L 4 (5.3,-0.7) - The damping ratio of the system. Its natural frequency w., damping corstart c, and stiffness coefficient k; for (m-1.25 kg). III- The amplitude of the motion if the phase angle is given as (0.4 rad). IV. Its initial conditions. (6.86, 0.5) 10 t[sec]
write Design spsecifcation for this system in small paragraphs
need answer in less than 20minutes would appreciate it so much
Answer letter a only.
Need only handwritten solution only (not typed one).
$+2.5$41 543834 2 8 b. A student has written a mathematical model for a rotational mechanical system without gears and some data were missing as shown below: [4s² + 2s +5 -25 as 0 -2s 3s² + 4s +6 -(1+B) 0 -6 3s +6 [0₁(s)] 0₂ (s 03(s)] What are the values of a and B? 2. What is the degree of freedom of the system? Sketch the expected rotational mechanical system and show thetorque, angular displacements and all values of inertias, springs, and dampers on the sketch with 85²2445445+8 their units. (89² +2+5+8) (33+4)
Give the following equations of motion and initial conditions: 8.0000 0.0000 52.0000 - 12.0000 0.3000 {x(t)}+ {x(t)}= 0; and {x,}= 0.0000 13.0000 12.0000 12.0000 0.6000 (0.0701 0.3465 If the modal matrix [S]= transform the initial conditions {x} into the modal coordinates {r,}. on 0.2718 -0.0550 2.2886 {r,} = 0.4026 4.7643 {r,} = 4.8800 (0.4027 {r,} = 2.2804 None 4.9584 {r,) = 5.0983 Clear my choice