Question  Vvvv  Modulation types in wireless communication systems? Explain in detail in terms of bandwidth requirements and resisting the disruptive effects in the system Full explain this question and tex t typing work only      We should answer our question within 2 hours takes more time then we will reduce Rating Dont ignore this line

Q: Transmission degradation is caused by attenuation, distortion, and noise. What would be the remedy,…

A:

Q: FM systems the modu lating frequeng Emalkiy the modulating vo Itaye Um - 2 voit, and the devintion…

A:

Q: Choose the correct Answer: type of a connector is semi precision and provides excellent performance…

A: To analyse the given question

Q: what will be the value of e^infinity?

A: The solution is given below

Q: A) state the types of communication channels? b) Why we need modulation, write the three types of…

A:

Q: In a feedforward system, the following error signal is kept at zero if __________. C = E and FF = F…

A: A feed-forward is a component or passage inside a control system that sends the signal which is…

Q: In economic dispatch neglecting loss case, the condition for the optimum operation is O dFn/dPn =A O…

A: Find explanation below

Q: The energy per bit to noise ratio for the following parameters is______________. C=1nW, N=1pW,…

A: In this answer we will find the Eb/No i.e. energy per bit to noise ratio as shown below.

Q: How would you calculate the Spacing between transmission lines?

A: The spacing between transmission lines is typically determined by various factors, including the…

Q: *Why is AM used for broadcasting in the communication systems? A. Its use avoids receiver complexity…

A: In this question we will write about amplitude modulation uses for broadcast and peak voltage of…

Q: For a twisted pair cable the attenuation measured is 5 dB and the Attenuation to cross talk ration…

A:

Q: Please examine the following two packets. What is the sequence number of the packet sent from port…

A: The sequence number of the packet sent from port 3224 to port 6020 From the given output

Q: Direct transmission of message signal without modulation can be cause. Problems Noise Fading…

A: These are the few questions related to the understanding of basic modulation techniques and their…

Q: A AD D DE AB E ЕН GH CH1 FG C BC1 H CH2 HF1 BC2 B HF2 Your task. Plan a route that begins and ends…

A: Connection Route- A valid path through which the data or the current pass through the whole circuit…

Q: A segment of the network where a single Ethernet packet can be transmitted is called Node O Hub O…

A: A segment of the network where a single Ethernet packet can be transmitted is called as Collision…

Q: You have a cable modem that transfers information at 20.0 Mbps. The bandwidth of the channel is…

A: According to the question we have to calculate the value of signal to noise ratio.

Q: Thicknet coaxial cable is less costly as compared to thinnet coaxial cable. Select one: True False

A: Thicknet coaxial cable is less costly as compared to thinner coaxial cable. True  or  False

Q: What is the role of modulation in the transmission of signals? How does modulation affect the…

A: Modulation plays a critical role in the transmission of signals, especially in various forms of…

Q: What has been developed to eliminate the effect of DC level in line coding.

A: What has been developed to eliminate the effect of DC level in line coding.

Q: DSB-SC (generartor/modulator) m4+cosakk NLD +) Coshet -m) |NLD find , & and . 'NLD= Non - Unean…

A:

Q: FIND NORTON EQUIVALENT CCT FOR THE CCT SHOWN BELOW. 2000 800 k Ix 50mA 8000 $8000

A:

Q: Explain Basic Trip Circuit in Transmission line? Also, Discuss the Fundamental Requirements of…

A: Protection refers necessary isolationof healthy system from faultysystem, so that fault can not…

Q: POPT Fao 2 10.20.20.0 /24 Fa0/o Se2/0 Router-P O Se3/0 192. 168. 1.0 /30 192. 168.2.0 /30 .2 R2 64…

A:

Q: Question     7 Find the generator matrix for a (21,8) 4-ary Hamming code. Use elements {0, 1, 2,…

A: A (21,8) 4-ary Hamming code is an error-detecting code that can detect and correct errors in a block…

Q: a) If the channel length is tripled, determine what happens to the transport time assuming diffusive…

A: Let the length of channel is l  Velocity is v

Q: Difference between technical ang operational definitions

A: Technical definition means a list of description that how the device is designed to work and what…

Q: a) In suspension insulator numbers of insulators are connected in series to fom a string and the…

A: We’ll answer the first question since the exact one wasn’t specified. Please submit a new question…

Q: For Q4 (i) and similar thing to (ii) and (iii) When calculating ni1/ni2 = (300/293.15)^1.5 I got…

A: Q. 4)(i) with respect to the calculation of ni1/ni2 = (300/293.15)^1.5

Q: Question 5 The AM modulation of a single frequency sinusoid (single tone information single) result…

A: The AM modulation of a signal frequency sinusoid (single tone information signal) results in?  A…

Q: Write different aspect detail of  Digital carrier systems.

A: A carrier systems is a mechanisms that provides a means to send signals from more than one source…

Q: Why we use the modulation ?

A: The explanation is as follows.

Q: How does fiber optic cabling work, and what advantages does it offer over traditional copper cabling…

A: Fiber optic cabling works by transmitting data in the form of light pulses through a core made of…

Q: In QAM, the which parameters of the carrier will be affected by the message? Phase O Niether O Both…

A: We need to select correct option for QAM .

Q: Describe the process of pre-emphasis. How does it improve communication performance in the presence…

A:

Q: El efecto del nivel de CD no es de peso en la escogencia de un código de linea Seleccione una: O…

A: Line code: It is the process of making digital data into digital signals. The line code is…

Q: What are the benefits of fibre-to-the-home or fibre-to-the-business project in a country?

A: A message signal is transferred from the sender to the receiver end. The signal is transmitted…

Q: Explain bridge T-attenuator andalso designit with anatenuation if 20dB. and terminatedinaloadof5002.

A: Given,  Bridge T-attenuator has, Attenuation =20log10K = 20dB Load impedance (ZL) = 500 ohm.

Q: How many transmission channels are required for full duplex?

A: Transmission channel required for full duplex  is 2.

Q: The cost of insulation for underground cable is less than the cost of insulation for TRUE / FAL…

A:

Q: Why modulation is necessary in communication system? Explain with at least three advantages of the…

A: The explanation is as follows.

Q: Question 12 How many receivers are required for half duplex transmission? 4

A: In half-duplex transmission, the sharing of information or communication happens in both directions,…

Code Conversion

The method or technique used to convert code from one format to another is termed code conversion. Code conversions are most commonly used in computers, digital electronics, microprocessors, etc.