Question Two The beam ABC in Fig Q2 is supported on pin and roller supports at points A and C respectively. Determine the slope and deflection at point B of the beam shown by the 1. direct integration method 2. Moment-area method Take E = 70 GPa and I = 335x106 mm4. -2 m- B 4 m Figure Q2 80 kN-m

Question Two The beam ABC in Fig Q2 is supported on pin and roller supports at points A and C respectively. Determine the slope and deflection at point B of the beam shown by the 1. direct integration method 2. Moment-area method Take E = 70 GPa and I = 335x106 mm4. -2 m- B 4 m Figure Q2 80 kN-m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Determine the slope and deflection at point B of the beam shown by doubu and anca moment method 10…

Q: 100 kN 300 kN–m A B 3 m 6 m 21 I E = constant = 70 GPa %3D I = 500 (106) mm %3D

Q: 6. Compute the slope and deflection at 4 m from the left support on the non-prismatic beam loaded…

A: Double Integration Method Step:1 Support Reactions

Q: Determine the slope and deflection at point A of the beam shown in figure below by conjugate beam…

A: Consider the free body diagram as; Consider the conjugate beam diagram for the given beam;

Q: A beam ABCDE supports a concentrated load P at its midspan as shown in the figure. a) Determine the…

Q: The cantilever beam loaded as shown has the following properties: El = constant. Using Double…

A: Using double integration method

Q: 4000 lb 1600 Ib/ft A C 7 ft- 3 ft-

A: When Simply supported beam is subjected to loading then they show some deflection that deflection we…

Q: 180 kN 15 kN/m B D -5 m- -5 m- -4 m- El = constant E = 70 GPa I = 2,340 (106) mmª %3D

Q: Solve the following using moment-area method. Draw the moment diagrams by part

Q: Using double integration method

A: Given Data E = 70 GPa = 70 × 103 N/mm2 I = 95 × 106 mm4 Determine the maximum deflection in the…

Q: 3. Compute the maximum deflection and the slope at A for the beam shown. Use any Method. E= 29,000…

Q: B. Frames Use the method of virtual work and determine the horizontal deflection at C. The…

A: Solution:-The given diagram is shown below,

Q: A simply supported beam has a span length of 13 meters. It carries a concentrated load of 5 kN…

A: E = 200 GPa I = 70 × 106 mm4 Determine the deflection at the point where the uniformly distributed…

Q: Using the virtual work method, determine: (a) The rotation at A (b) The deflection at B (c) The…

A: A beam is there in which two loads are acting on it we need to find out the following by using…

Q: Using any of the three Geometric Methods, answer the following beam. Indicate the negative sign (-)…

A: Let's use double integration method ( type of geometric method) to solve this problem

Q: The cantilever beam is a 10 in length carbon steel bar, with a diameter of 1 in. And it is charged…

A: Given a cantilever beam of 10 in length,Diameter is 1 in

Q: 90 kN b. 5 m El = constant E = 200 GPa = 800 (106) mm4 %3D

A: Direct integration method: Direct integral method is a type of structural method used to calculate…

Q: Using the slope-deflection method, determine the end moments and the reactions at the supports of…

A: Given Data:E=200Gpa = 200×109N/m2=200×106kN/m2I=213×106mm4=213×10-6m4Suppoprt B settles by…

Q: AK N zm zm

Q: Determine the slope at A and B and the deflection at C for

Q: Use the principle of virtual work to determine the rotation at Support B. (The positive direction of…

A: Given that, Point load at C = 35 KNLength of Span AB, L =4 m.Length of Span BC, L1 =1.6 m.Youngs…

Q: 180 kN F2sm -2.5 m- -5 m El = constant E = 200 GPa I = 1700 × 10º mmª Use the conjugate beam method…

Q: A simply supported beam is loaded as shown in the figure. Determine the slope and deflection at the…

A: calculate reaction RA+RB=5+7=12ktaking moment about BRA×11-5×7-17.5=0RA=4.77kRB=6.22k write moment…

Q: El is constant for the beam shown in Figure 4. • Compute the rotation of the beam at B. • Compute…

Q: Determine the deflection at point D and the maximum deflection of the beam in the figure using…

Q: Determine the slope and deflection at point B of the beam shown by double integration metho 50 kN ·…

A: To find slope and deflection at B

Q: Use the moment-area method to determine the slopes and deflections at point C of the beam shown.

A: Use the moment-area method to determine the slopes and deflections at point C of the beam shown.

Q: 2. Determine the slope and deflection at point B of the beam shown by double integration method. -6…

A: Given data E = 10,000 ksi I = 800 in4 Find slope and deflection at point B using double…

Q: 15kN A 2m 3m 25kN/m 5m 14m 4m QUE

A: Given data:

Q: Part 2: for the frame shown below, P=20 kN and a=2 m, Assume I=20000 in and E=30,000 ksi for all…

A: Given:P = 20 kNa = 2mI = 20000 in4E = 30000 ksiRequired:Vertical deflection of E

Q: 1. By using Double Integration Method, Determine the deflection at the midspan of the beam shown. 30…

A: Given: E=200 GPaI=1460×106 mm4 An overhanging beam with hinge support at A and roller support at B…

Q: 1. Determine the slope and deflection at point B of the beam using the conjugate- beam method. -2 m-…

A: 1) Calculation of Reactions: ∑MC=0(VA×4 )+ 80=0VA=-804=-20kN∑Fy=0VA+VC=0VC-20=0VC=20kN∑Fx=0H=0 2)…

Q: Determine the slope and deflection at point A of the beam shown by the double integration method. Q.…

Q: 30 kN/m A B 5 m –2 m El = constant E = 200 GPa I = 146(106) mm4

Q: Base on the Conjugate beam. Determine the corresponding deflection at the free end of the given beam…

A: A cantilever beam is loaded as follows

Q: For Beam AB (EI Constant), use the Unit Load Method to Determine: 1. The Deflection at C 2. The…

Concept explainers

Beams and Frames

A beam is a horizontal structure or a member which is always subjected to transverse shear loads.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step by step

Solved in 5 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

use virtual work method to determine horizontal and vertical components of the deflection at joint B of the truss P D A E B -2 at L EA= = constant P A F |--
QUESTION 2 - BEAM For the beam shown below, determine the vertical deflection at point B by using the virtual work method. EI is constant. -5 ft A -5 ft 12 k Į -5 ft B -5 ft- 70 k-ft Fig. 2
2. Use the virtual work method to determine the horizontal deflections at joint C of the frame shown. 20 kN B B 3 kN/m olish br 10 m H C 10 m El= constant E = 200 GPa 1=400(106) mm²
Problem 5 The cantilever beam shown below is non-prismatic and is loaded with a concentrated load at free end B. Determine: a) the vertical deflection at B, b) the rotation at B (use either double integration or moment area) A is ft I₁ = 6000 in 4 10 ft = 3000 in 4 H 20 B K E=29000 ksi
1. The beam with, cross-section shown, is subjected to the load shown. Using E=200 GPa, determine the defection at D and the maximum deflection by double integration method. 80 mm 25 mm 4 kN/m 16 kN 25 mm B D 140 mm 6m 4m 2m 25 mm 120 mm
3. Determine the deflection at point C for the beam shown by the virtual work method. 3 kN/m A D C 5 m 10 m 5 m I 21 I E = constant = 250 GPa I = 600(106) mm4
Determine the slope and deflection at point B of the beam shown by the moment-areamethod.
Use the moment‐area method to determine the slope and deflection at point B of the beam.
A prismatic uniform beam has a total length of 4L, a moment of inertia I, and a modulus of elasticity E. The beam is embedded at A, simply supported at B, and subjected to the distributed load q shown. Calculate:a) The reactions and moments in A and B.b) Deflection and slope at point C. You must indicate their directions.
Solve using: (Complete Solution) A. CONJUGATE BEAM METHOD B. VIRTUAL WORK METHOD Determine the deflection at point B of the beam shown in the figure. Values for the moment of inertia of each segment are indicated in the figure. Take E = 200 GPa.
Determine the horizontal and vertical deflections at D for the frame shown below (consider E, I constant and neglect axial deformation). P |2L A В C 4L
Solve using conjugate beam method