QUESTION ONE A three-phase 20 MVA, 11 kV generator has a reactance of 10% and is connected via a bank of three single-phase transformers to a transmission line whose series reactance is 100 2. The transmission line is supplying a load of 10 MVA at 10 kV and 0.8 power factor. The transformer bank at the generator end is connected in delta on the generator side and in star on the transmission line side and the transformer on the load side is star-star connected. Each of the single phase transformers in the bank of transformers is rated at 10 MVA, 11/110 kV with a reactance of 8%. Draw the pu circuit diagram for a system base of 10 MVA, 15 kV in the load circuit. Calculate the voltage at the generator terminals.

QUESTION ONE A three-phase 20 MVA, 11 kV generator has a reactance of 10% and is connected via a bank of three single-phase transformers to a transmission line whose series reactance is 100 2. The transmission line is supplying a load of 10 MVA at 10 kV and 0.8 power factor. The transformer bank at the generator end is connected in delta on the generator side and in star on the transmission line side and the transformer on the load side is star-star connected. Each of the single phase transformers in the bank of transformers is rated at 10 MVA, 11/110 kV with a reactance of 8%. Draw the pu circuit diagram for a system base of 10 MVA, 15 kV in the load circuit. Calculate the voltage at the generator terminals.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q3) What are the elements finding from no-load test of single phase transformer? Q4) Why Transformer Rating in kVA? Q5) How can eddy current loss be minimized?
1. A single-phase power system as shown in Figure 1 consists of a 240 V, 60 Hz generator supplying a load, Zod = 8 + j6 Q through a transmission line of impedance, Zne = 0.08 + j0.14 Q. Answer the following questions: (1) transformer, T; and T2. Determine the voltage at the load and transmission line losses without the (ii) Determine the voltage at the load and transmission line losses with the transformer, T, and T2. T1 T2 1:10 10:1 IG Zaine Zioad source Figure 1
C2 (i). Draw the Schematic diagram and explain the working of LVDT and write any two applications of it. (ii) A 12 kVA, 56HZ, single-phase transformer has a turns ratio of 18 : 2 and is supplied from a 2.5 kV supply. Neglecting losses, determine (a) the secondary voltage, (b) the full load primary current, (c) the maximum flux and (d) the minimum value of load resistance which can be connected across the secondary winding without the kVA rating being exceeded secondary voltage primary current maximum flux secondary resistance
A 4-bus three-phase power system consists of the following equipment: • Generator 1 connected to bus 1 with a rated power of 20MVA, rated voltage of 20 kV, and a series reactance of 0.4 p.u. • Generator 2 connected to bus 5, with a rated power of 12MVA, rated voltage of 10 kV, and a series reactance of 0.3 p.u. Transformer 1 connected between buses 1 and 2, is wye-wye connected with a rated power of 20 MVA, rated voltages 20/100 kV, and a series reactance of 0.1 p.u. • Transformer 2 connected between buses 4 and 5, is wye-wye connected with a rated power of 12 MVA, rated voltages 12/110 kV, and a series reactance of 0.15 p.u. • Transmission Line 2-3 connects buses 2 and 3 and had a series impedance of 50 + j75 ohms. • Transmission Line 3-4 connects buses 3 and 4 and had a series impedance of 40 + j80 ohms. • Load A connected to bus 3 and abosorbes20 MW and 10 MVAR. The voltage at bus 3 is 105 kV. 1) Draw the one-line diagram for the system. 2) Draw the per-unit, per phase…
A 220-kVA transformer with .2% resistance and 4% reactance and another 120-kVA transformer with 3% reactance and .15% resistance with the same voltage ratio. the phase angle is 33 degree and the total load .25 MVA. How much the load of each transformer. what are the load currents of each transformer if a1 =20 and a2=25?
Please answer all subparts than i will like a. A current transformer (CT) is rated 200/5 and has a secondary current of 4.0 A. Determine the primary current. b. A 150/5 CT has the primary conductor looped to pass through the donut three times. If the secondary current is 3.0 A, determine the primary current. c. A 60/5 CT has the primary looped to pass through the donut two times. With 25 A in the primary, determine the secondary current. d. A voltage (potential) transformer is rated for 14.4 kV / 115 V and is used to measure the voltage on an industrial power line. If the voltmeter indicates 111 V, calculate the voltage in the power line.
Choose the correct statement of a no load single phase transformer from the following O a. The magnetizing component of no load current (Im) leads the core loss component of no load current (Ic) O b. The magnetizing component of no load current (Im) lags the core lossComponent of no load current (Ic) O c. The magnetizing component of no load current (Im) and the core loss component of no load current (Ic) are in phase each other O d. The magnetizing component of no load current (Im) leads the core loss component of
2.2. The figure below shows a radial transmission system with a generator having a per-unit voltage of 1.3 at an angle of 9 degree p.u. The load demand is 47MW at a power factor of 0.96lagging. Use the nameplate values of Transformer 2 as base values and calculate the following: Correct answers to three decimal places : 25..Per unit impedance of transformer and it's angle 26.Per unit voltage of the line and its angle 27.Per unit impedance of the line and its angle. And Reactance of the transmission line when the load consumes full-load (Ω).
Solve the following problems with complete solutions and units usingtwo(2) decimal digits.2. A 5-kVA transformer has 35 W. core loss and 40 W. copper loss atfull-load. It operates at rated kVA and 0.8 power factor lagging for 6hours, one-half rated kVA and 0.5 power factor lagging for 12 hoursand no-load for 6 hours. What is the all-day efficiency?
The Y/Y connected 3-phase step-up transformer has a rating of 1200 MVA, operating at 33 kV/340 kV and 60 Hz. Its impedance is characterized solely by a reactance of 11.5 percent. Its purpose is to increase the voltage from a generating station in order to supply power to a 340 kV transmission line. Answer the following questions: a) Draw and determine the equivalent circuit of this transformer, per phase, in per-unit. b) Using the per-unit method, determine the generator terminal voltage when the high-voltage (HV) side of the transformer supplies 800 MVA at a power factor of 0.90 with a lagging angle, and the voltage is 360 kV. Hint: Select the nominal voltage as a base voltage, and the nominal power rating as a base power.
It is bartleybe's policy that if questions objective than you need to solve at least first 3 questions.