ASAP by hand not using AI or gpt Question No. 2a)For the circuit shown in Figure 2(a).calculate the following:R₁R₂Itotal resistance across the source80 V560 0.156II. total current from the sourcePage 1 of 3www71002R₁1.0 kRsR₁Rs5601.0 k5600R6Rgwwwww2.0kfFig. 2(a)460 2

a)R4 and R6 are series, R46 = 1 + 2 = 3 kohm = 3000 ohm R46 and R5 are parallel, R456 =…

Answered: Question No. 2 a) For the circuit shown…

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter7: Parallel Circuits

Section: Chapter Questions

Problem 3PP: Using the rules for parallel circuits and Ohmslaw, solve for the missing values....

See similar textbooks

Similar questions

....hdhddd...
The schematic is step 7
Calculate the equivalent resistances Rin of the following circuits. (The resistance value of the diodes in the conduction will be 0, the resistance value of the diodes in the insulation will be taken as infinity. R1=10ohm
Part A What must the emf E in the figure (Figure 1) be in order for the current through the 7.00 N resistor to be 1.65 A ? Each emf source has negligible internal resistance. Express your answer with the appropriate units. E = Value Units Submit Request Answer Figure Provide Feedback Next > 24.0 V Ţ §7.00 $2.00 3.00 N
Given the zener voltage at 9V and the zener power at 1W, what is the range of allowable values of Iz (operating values). Choices: 0.11A 22mA to 89mA 9A 0.11A to 9A Plss show complete solution
3.- For the following circuit, determine the following:(a) Currents in each branch. b) Potential differences between each branch (from junction to junction). c) Electric potentials in each junction with respect to ground
A direct current of 12.5 A flows in a 25-ohm resistance. Determine the maximum value of an alternating current that will produce heat at the same rate in this resistance. Expresss answer to the nearest hundredths.
Solve asap
A PMMC instrument has a three-resistor Ayrton shunt connected across it to make an ammeter as in Figure 2. The resistance values are R1 = 4.52, R2=0.452 and R3= 0.052. The meter has Rm = 1k2 and Ifs.d = 50µA. Calculate the three ranges of the ammeter. [10.05mA, 100.05mA, 1.005A] Rm=1k2 B R3 R R, Selector Figure 2 수
Suppose the three branch currents in this circuit are I₁ = -3 A, I₂ = -18 A, and I3 = -15 A. The voltage drop across each circuit element is as given in the table below. From this information, determine, for each of these circuit elements, (i) whether an active or passive sign convention is being used for that element, (ii) whether that element is absorbing or producing a net (positive) amount of electrical power. In each answer box within the table below, type the correct choice from among the bold-faced words above. V₂ B A B A C D 1₁ A B 1₂ 1₂ + Circuit element Voltage drop Sign convention? Absorbing or producing net electrical power? -9 V -2 V C 9 V -11 V D
A circuit has resistance of 20 ohms and a reactance of 30 ohms. What is the power factor of the circuit? a. 0 b. 0.55 c. 0.832 d. 0.99
When a voltage of 100V at 50Hz is applied to a choking a coil A, the current taken is 8A and the power is 120W, when applied to a coil B, the current is 10A and the power is 120W. what power will be is 10A and the power is 120W. what power will be taken when 100V is applied to the two coils connected in series?

SEE MORE QUESTIONS

Recommended textbooks for you

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Power System Analysis and Design (MindTap Course …

Electrical Engineering

ISBN:

9781305632134

Author:

J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:

Cengage Learning

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Power System Analysis and Design (MindTap Course …

Electrical Engineering

ISBN:

9781305632134

Author:

J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

Question No. 2 a) For the circuit shown in Figure 2(a). calculate the following: R₁ R₂ I total resistance across the source 80 V 560 0. 156 II. total current from the source Page 1 of 3 www 71002 R₁ 1.0 k Rs R₁ Rs 560 1.0 k 5600 R6 Rg www ww 2.0kf Fig. 2(a) 460 2