Question No. 18: (a) In an epicyclic gear train, an arm carries two gears A and B having 36 and 45 teeth respectively. If the arm rotates at 150 r.p.m in the anticlockwise direction about the centre of the gear A which is fixed, determine the speed of gear B. If the gear A instead of being fixed, makes 300 r.p.m in the clockwise direction, what will be the speed of gear B? (b) Prove that the resultant unbalanced force is minimum when half of the reciprocating masses are balanced by rotating masses.

Q: There are two adjacent gears A and B, with 23 and 42 teeth respectively. Initially, both gears are…

A: Given:Gear A rotates clockwise initially and gear B rotates counterclockwise , and consider the…

Q: S3 Ts4 uniform spe T= 81 it shafi E rotates at a

A:

Q: A follower plate B holds a pair of 26-tooth planet gears C against a 20-tooth sun gear A. Each plan…

A:

Q: in a planetary gear train, the arm C caries two gears A and B and a compound gear D-E. The gear A…

A:

Q: Original Question: The figure below represents a pair of bevel gears A and B. Gear A rotates in a…

A: Given:The angular velocity of member OC is equal to the angular velocity of gear B because gear A is…

Q: Gear 2: N2 = 25 teeth and Pd = 20 per in Gear 3: d3 = 3.5 in Gear 4: N4 = 28 teeth Gear 5: d5 = 4…

A:

Q: rotates at a uniform speed

A:

Q: Consider the gear/pulley mechanism shown below (top view). The gear on the lower left is driven at a…

A:

Q: le a reverted train Fig. (1), An arm A Carries two concentric separate wheels B and C a compound…

A:

Q: L. = = 10

A: The angular velocity of member OC is equal to the angular velocity of gear B because gear A is…

Q: 12. The gear A on the drive shaft of the outboard motor has a radius r = 0.5 in. and the meshed…

A: Introduction: In an assembly, a pinion is the smallest of two meshed gears. Depending on the…

Q: 25. In the Humpage gear shown in Fig. 13.20, the wheel C is fixed and shaft X rotates at 650 r.p.m.…

A: Given data :-Speed of shaft X = 650 rpmTeeth of gear TA =  18      ;    TD = 24…

Q: 12. The gear A on the drive shaft of the outboard motor has a radius r = 0.5 in. and the meshed…

A:

Q: 014 -15 Pinion gear A rolls on the gear racks B and C. If racks B and Care fixed, determine the…

A: Solution to Q14 as mentioned by the student:

Q: (5) In the combined gear train shown in figure, Z₁-20, Z₂-25, Z₁-15, Z₁¹-30, Z4=70, Z4²=60, nµ=110…

A: given; number of teeth;Z1=20Z2=25Z3=15Z1'=30Z4=70Z4'=60speed(nH)=110rev/minspeed(n1)=?

Q: ram above, RA = 0.339 m, while Rg = 0.776 m. A and B are intermeshing gears (I just u the teeth)…

A:

Q: The spur gearing arrangement  made of two parallel shafts,whose pitch circle diameters of driven and…

A: Gear: The gear is rotating part of the mechanical device. The gears are having the number of teeth…

Q: Consider the following epicyclic gear trai The number of teeth is indicated in the figure. Crown…

A:

Q: The lathe machine in the Central University of Technology mechanical workshop uses epicyclic gear…

A:

Q: A gear reduction system consists of three gears A, B, and C. Knowing that gear A rotates clockwise…

A:

Q: Question 4 rA= 50 mm TB = 120 mm rc= 85 mn If the gear A shown in Figure 5.13 is initially turning…

A:

Q: If gear A rotates with a constant angular acceleration of aA = 89 rad/s2, starting from rest,…

A: Introduction If two or more gears are installed on the same shaft in a compound gear configuration,…

Q: 5 Pinion gear A rolls on the gear racks B and C. If racks B and C ar determine the acceleration of…

A: 14 Ans:  B is correct 15 Ans: D is correct 16 Ans: E is correct

Q: The 40.64 cm. diameter pulley of a gasoline engine is connected by a belt (which is assumed not to…

A:

Q: Two gears of radii 3 inches and 6 inches are used on a small construction site concrete mixer.…

A: Gear is a element used to transfer the rotatory motion from one shaft to other over a specified…

Q: Spur gear train is used to transmit the power of 2kW from input gear A rotating at 120 rpm to output…

A:

Q: In the figure shown, the load needs to be raised 28 ft. Noting that Gear A is initially at rest and…

A: given; speed (N)=120rpmat time (t)=5s

Q: Given the system of gears below, the double gear is free to move along the horizontal.Determine the…

A: The free-body diagram of the system of gear is shown below.

Q: In order to change the direction of rotation a planetary gear is fitted with a compound planet gear…

A: Given data, The gears 3 and 4 is compound gear. Power of the motor, P = 5 kW = 5000 W No of teeth of…

Q: Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be…

A: Draw vector loop diagram.Here  indicates vectors and consider  are angle made by vectors  in counter…

Q: The planetary gear train shown in the image below has 16 teeth on the sun and 22 teeth on the…

A:

Q: Q: The sunwheel D has 20 teeth, the gear is 50 teeth, internal gear C is fixed. The input shaft…

A: Sun wheel Arrangement  Given Data The sun wheel teeth D , ZD=20 The sun wheel teeth C, ZC=50 Input…

Q: Gear 2: N2 = 25 teeth and Pd = 20 per in Gear 3: d3 = 3.5 in Gear 4: N4 = 28 teeth Gear 5: d5 = 4…

A:

Q: The figure below represents a pair of bevel gears A and B. Gear A rotates in a horizontal plane…

A: The angular velocity of gear A is .The angular velocity of OC shaft is .

Q: A motor gives gear A an angular acceleration of a = (2+0.0060²) rad/s², where 0 is in radians.…

A:

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.