Table 6. Equivalent Resistance, Voltage and Current Distribution in Parallel ConnectedResistorsCalculated DataMeasured DataResistance (N)CurrentVoltage DropCurrent (A)Voltage Drop(A)(V)(V)R =VI, =%3DR, =I, =V, =I, =V, =R3 =I =V, =I =V, =R123V3=%3DQuestion: Show how you did the calculation of current passing through the resistors forTable 6.Your Answer:Question: In measuring the current through a resistor, the ampermeter is placed in series withthat particular element. What would happen if we tried to measure the resistor current byplacing the ampermeter in parallel with the resistor? Would that allow us to measure thecurrent through the resistor?Your Answer:||

No, it would not allow to measure the current through the resistor.

Question: In measuring the current through a resistor, the ampermeter is placed in series with that particular element. What would happen if we tried to measure the resistor current by placing the ampermeter in parallel with the resistor? Would that allow us to measure the current through the resistor?

Question: In measuring the current through a resistor, the ampermeter is placed in series with that particular element. What would happen if we tried to measure the resistor current by placing the ampermeter in parallel with the resistor? Would that allow us to measure the current through the resistor?

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

The figure below shows a simplified model of a cardiac defibrillator, a device used to resuscitate patients in ventricular fibrillation. S R Rorso + The capacitor C charge through the resistor R (when the switch S is toggled to left) and discharge current through the patient's torso which is of resistance (when the switch S is toggled to right). This phenomenon allows the heart's normal rhythm to be reestablished. (a) If the capacitor is initially uncharged with C = 7.0 µF; ɛ = 1240 V, find the value of R (in ohms) required to charge the capacitor to a voltage of 800 V in 2.1 s. (b) If the capacitor is then discharged across the patient's torso with Rtorso = 1200 Q, calculate the voltage (in V) across the capacitor after 4.0 ms.
5. This problem is about charging a weak battery & = 10.8 V with a good battery &, = 12.0 V. Let the internal battery resistances be r₁ = r₂ = 0.022, and resistance of the charging cable be R = 0.02 02. Also, let the current I leave the good battery. (a) In the picture below, the battery is hooked up correctly, with the positive terminals connected to each other. Apply the loop rule to this circuit and find the current charging the battery. WH $5 R No (b) In the picture below, the battery is hooked up incorrectly. Find the current charging the battery. www R
22. A resistor R is connected to a battery dissipates energy at the rate P. If another resistor is connected in parallel with R, the power dissipated by R is * O Less than P O P O More than P O Any of the above, depending on the values of the resistances 23. The second resistor of question 22 is connected in series with R. The power dissipated by R is now * OLess than P O P O More than P OAny of the above, depending on the values of the resistances
The circuit below involves a 90 V battery, three resistors (10N, 15N, and 202), and three capacitors (0.015F, 0.03F, and 0.03F). The switch stays on position "a" for a long time to reach a stable state. At t= 0 the switch is quickly toggled to position "b". How long after the switch is moved to position"b" will the current through the 202 is equal to 0.9A. 150 102 90 V- 0.03F + 0.015F. 0.03F 20.00
What do you expect the resistance of a fully- discharged capacitor to be? Why? What do you expect the resistance of a fully-charged capacitor to be? Why?
The pedestrian crossing of Washington Road and Ivy Lane (near the Physics building) needs a back-up battery in event of power failure. In order for the three lights to be bright enough to be seen in daylight, each of the three RL = 50 N lights must dissipate P = the 3 lights are connected in parallel (see the drawing), and the open circuit voltage of the battery (that is, the voltage when there is no current) is Vo = 110 volts. What is the maximum internal battery resistance R; allowable given that each lamp must dissipate 220 watts? 220 watts. Suppose %3D %3D Ri Vo RL pyri
In the Wheatstone bridge experiment shown in 2,2 kn the figure the values of the resistors are R=2.2 k2, R2=4.7 k2, R3=3.3 k2 .Calculate the value of resistor R, when the current in the HA ampere-meter is zero. R2
The figure below shows a simplified model of a cardiac defibrillator, a device used to resuscitate patients in ventricular fibrillation. R HINT E S C When the switch S is toggled to the left, the capacitor C charges through the resistor R. When the switch is toggled to the right, the capacitor discharges current through the patient's torso, modeled as the resistor Rtorso, allowing the heart's normal rhythm to be reestablished. R torso V (a) If the capacitor is initially uncharged with C = 7.25 µF and E = 1220 V, find the value of R (in ohms) required to charge the capacitor to a voltage of 755 V in 1.60 s. Ω (b) If the capacitor is then discharged across the patient's torso with Rtorso = 1270 , calculate the voltage (in V) across the capacitor after 4.50 ms.
The capacitor in the circuit shown is fully charged by a 24 V battery. The switch is closed at t = 0. At sometime after the switch is closed, the voltage across the capacitor is measured to be 10 V. What is the current in the circuit at this time, in Ampere? C = 3.0 µF, and R = 2.0 02. Your answer needs to have 2 significant figures, including the negative sign in your answer if needed. Do not include the positive sign if the answer is positive. No unit is needed in your answer, it is already given in the question statement. Cil
A 120 volt household circuit has a 360-Watt blender and a 30ohms light connected to the source in parallel: A) How much current (amps) must the source provide? B) How much power (Watts) is used in the 30ohms light?
In measuring the current through a resistor, the ampermeter is placed in series with that particular element. What would happen if we tried to measure the resistor current by placing the ampermeter in parallel with the resistor? Would that allow us to measure the current through the resistor?
(a) The resistance between two well-separated points on the human body is about1.5 x 10. If a potential difference of 120 V is applied across these points, how much current is generated? (b) If the skin is wet, the resistance drops to 5.0 x 10. What will the current be in this case for an applied potential difference of 120 V?