A resistor is made out of a long wire having a length L. Each end of the wire is attached to a terminal of a battery providing a constant voltage Vo. A current / flows through the wire. If the wire were cut in half making two wires oflength L2, and both wires were attached to the battery (the end of both wires attached to one terminal, and the other ends attached to the other terminal), what would be the total current flowing through the two wires? 0 21 01 041 012

A resistor is made out of a long wire having a length L. Each end of the wire is attached to a terminal of a battery providing a constant voltage Vo. A current / flows through the wire. If the wire were cut in half making two wires oflength L2, and both wires were attached to the battery (the end of both wires attached to one terminal, and the other ends attached to the other terminal), what would be the total current flowing through the two wires? 0 21 01 041 012

Related questions

Q: The total amount of charge in coulombs that has entered a wire at time t is given by the expression…

Q: A circular coil enclosing an area of 120 cm is made of 210 turns of copper wire (shown in the figure…

A: Solution:-Given thatArea of circular coil (A)=120 cm2=0.012 m2Number of turns (N)=210 turnsR=7…

Q: You wired an electric lamp and an electric stove in parallel to an ideal battery with emf, & =…

A: This problem is from Network circuitry. Let's solve this problem by using Ohm's law. Please have a…

Q: A current-carrying ohmic metal wire has a cross-sectional area that gradually becomes smaller from…

A: Drift velocity is the average velocity of charged particles when an external electric field is…

Q: A 0.1-A current flows through of a copper wire of length 1.0 m for 20 minutes. The diameter of the…

Q: The current in a wire varies with time t according to the relation: I(t) = 3+3t². where the current…

Q: The following graph represents the charge-discharge profile of a Li-ion battery in the 1st and 50th…

Q: onducting sphere is charged by an emf source E through a 1.00 M stor. When the sphere is fully…

Q: Calculate the diameter of a 0.04-cm length of tungsten filament in a small lightbulb if its…

Q: A long wire with a radius of 0.450 cm carries a current. The potential difference across a 3.20 m…

Q: A rectangular block of copper has sides of length 14 cm, 26 cm, and 41 cm. If the block is connected…

A: The actual current, if the 8 volt source is a theoretical perfect source, can be done by calculating…

Q: A wire has a radius of 2.5 m. The current density carried by the wire is a function of distance…

A: As it is well known that the current and current density are related as:…

Q: When a current of 0.218 A is present in a wire 20.0 m in length with cross-sectional area 8.19 x 10…

Q: The magnitude J of the current density in a certain wire with a circular cross section of radius R =…

Q: The charge in an electronic device satisfies Q(t) = 4.15t³ + 2.72t + 3.28/t² Coulombs. What is the…

A: Given Data :Charge as a function of time is given asQ(t) = 4.15t3+2.72t+3.28t2 Let I denotes the…

Q: Currents up to 30 A can be carried by 10 gauge copper wire. (a) What is the resistance of 80 m of 10…

Q: The drift speed in a copper wire is 7.15 x 105 m/s for a typical electron current. Calculate the…

Q: The unspecified currents in (Figure 1) are IA = 3 A and ID = 3 A. The directions of the currents are…

A: The current in both parts have been calculated with explanation. If any doubt please feel free to…

Q: In the figure current is set up through a truncated right circular cone of resistivity 731 02-m,…

A: The current i enters the truncated cone at left end and leaves at the right end. Let this represent…

Question

A resistor is made out of a long wire having a length L. Each end of the wire is attached to a terminal of a
battery providing a constant voltage Vo. A current / flows through the wire. If the wire were cut in half
making two wires oflength L/2, and both wires were attached to the battery (the end of both wires attached to
one terminal, and the other ends attached to the other terminal), what would be the total current flowing
through the two wires?
0 21
01
0 41
012
014

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Trending now

This is a popular solution!

Step by step

Solved in 4 steps

SEE SOLUTION Check out a sample Q&A here

Similar questions

5. Consider two (1 and 2) wires both having constant circular cross sectional areas: wire 1 has diameter = d, ; wire 2 has diameter = d. Potential differences are applied across each wire so that they both carry current. The current in wire 1 is I, and in wire 2 it is I, ; the the magnitude of the current density in wire 1 is J, and in wire 2 it is J,. If I,= I, and J, = (2) J, then wire diameters must be such that d, = (?) d. a. 2/2 b. V212 c. 2 d. V2 e. V214
this problems is giving me hard time
Current and Resistance Problem 17: An unknown wire in a circuit has a circular cross-section with diameter 2.5 mm. It carries a current of 8.8 mA. Part (a) What is the current density, in milliamperes per square centimeter, in this wire? Part (b) If you assume the drift velocity in this wire is 1 × 10-2 cm/s, what is the density of charge carriers per cubic centimeter? Part (c) If the conductivity in this wire is 1.5 × 106 Ω-1 m-1, what is the average time between collisions, in nanoseconds?