QUESTION FIVE The boost regulator has an input voltage, Vs = 9 V. The average output voltage, Va = 15 V and average load current, la = 0.8 A. The switching frequency is 20 kHz. If L = 300µH and C = 440µF, determine (a) the duty cycle & (b) the ripple current of inductor, AI, (c) the peak current of inductor, I₁, (d) the ripple voltage of filter capacitor, AV, and (e) the critical values of L and C.

Q: A full-wave rectifier operating from a 60HZ supply develops a peak rectifier voltage of 23V.…

A: Ripple factor is given by where, and, f=60 C=223uF Idc = 76mA

Q: Consider two reverse biased diodes. If the ratio of applied reverse bias voltages is 0.5, find the…

A: We need to find out capacitance ratio for given voltage ratio

Q: Three phase Bridge rectifier operated from a 380V, 50Hz source throughout three-phase Y/Y connected…

A: Given data Average thyristor current 15ACircuit inductance per phase 1.2mH

Q: Specify the LM-series linear regulator required to regulate a fixed voltage of 14 V. Please write…

A: To specify the LM-series linear regulator that is suitable for maintaining a stable voltage of 14 V.

Q: idecal diode R ffechive vecue frequency equal to GoHe. the voltage ripple at the terminals of R is…

A: Note: All the given options are incorrect  Please follow my solution..  Here Veffective = Vrms = 120…

Q: b. Suggest a circuit that eliminates the negative portion of an AC waveform, leaving the positive…

A: Note:As discussed in the question, we are required to answer only part (b). we are required:To…

Q: Suppose we have a 10-Hz sinusoidal voltage source, vin(t). Draw the diagram of a circuit that clamps…

A: Drawing a circuit that clamps the positive peaks to - 4 V

Q: Specify the LM-series linear regulator required to regulate a fixed voltage of -9 V. Please write…

A: To specify the LM series linear regulator required to regulate a fixed voltage of -9 V

Q: Veut Vin Vu 1kN 1kN c) c) Vin Veut Vin

A: *Multiple Sub- parts*   # as per our guidelines we are supposed to answer ?️only first 3️⃣…

Q: A 50 Hz sinusoidal AC voltage source of peak value V, = 340 V delivers power to a resistive load of…

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: We want to investigate how the field strength will be with air as dielectric and with steatite. A…

A: Parallel plate capacitor, Line voltage, VL=24 kV. Area of parallel plate A=1 m2. Distance between…

Q: varies between 2 mA and 33 mA, and the diode is an ideal 4 V Zener diode. You will need to…

A: As per our company guidelines we are supposed to answer only first question kindly repost the other…

Q: Specify the LM-series linear regulator required to regulate a fixed voltage of -7 V. Please write…

A: To specify the LM-series linear regulator required to regulate a fixed voltage of -7 volts.

Q: For the given circuit below, a step down transformer gives an RMS voltage of 230 V/ 15.2- 0-15.2 V…

A: Peak inverse voltage of diode?  This circuit is centre tap. Full wave rectifier

Q: What will be the output of the following circuit? (Assume 0.7V drop across the diode) * 18H62 ...…

A: Here the diode is On condition and , diode is On it is replaced with 0.7v battery.     V = 12 -0.7…

Q: Specify the LM-series linear regulator required to regulate a fixed voltage of -19 V. Please write…

A: To specify the LM-series linear regulator that is suitable for maintaining a stable voltage of -19…

Fault Analysis

In an electrical engineering system, a fault is an abnormal electric current flowing through the system, and fault analysis is the study of these faults. For instance, a short-circuit is a fault where the live wire touches the ground or neutral wire. If a circuit is interrupted by a failure of a current-carrying wire then an open circuit fault occurs. The open-circuit faults are also called series faults. One or more phases or ground may be involved in a three-phase fault or may occur only between two phases. Current flows into the earth in case of a ground fault or earth fault. For most situations, the prospective short circuit current of a fault that is predictable can be calculated. To limit the loss of service because of a failure, the protective devices can detect fault conditions and operate circuit breakers and also other devices. All phases equally can be affected in a poly-phase system which is known as symmetric electrical fault. The asymmetric fault becomes more complicated to analyze if only some phases are affected. By using methods such as symmetrical components, the power system analysis of these types of faults is often simplified. The main objective of power system protection is to design, detect, and interrupt power system faults.