Question Five A 50mm diameter solid bar is drilled axially and concentrically to a depth of 90 mm with a 20mm diameter hole. The bar is then loaded by a torque, which produces a maximum shear stress of 86 MN/m² in the bar. The total angle of twist is measured to be 0.65 degrees. Determine a) the applied torque b) the total length of the bar Take the Modulus of Rigidity as 75 GN/m2

Question Five A 50mm diameter solid bar is drilled axially and concentrically to a depth of 90 mm with a 20mm diameter hole. The bar is then loaded by a torque, which produces a maximum shear stress of 86 MN/m² in the bar. The total angle of twist is measured to be 0.65 degrees. Determine a) the applied torque b) the total length of the bar Take the Modulus of Rigidity as 75 GN/m2

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Link AB, of width b = 2 in. and thickness t = 1414 in., is used to support the end of a horizontal beam. The average normal stress in the link is -18 ksi and the average shearing stress in each of the two pins is 12 ksi. Determine the average bearing stress (ksi). **The way I had solved it was that I used the given normal stress to first find the P force needed to plus into my bearing stress formula. I still however need the diameter. The answer key says to use the given shear stress equation to find the diamter, how do you know to use that and not the shear stress formula again?
1. A steel shaft is subjected to the torques shown. The shaft is solid with a diameter of 1 in and G = 12,000 ksi. Determine: (a) internal torque (lb ft) in each segment. Include the necessary diagram to show these internal forces (b) maximum shear stress (psi) in each segment (c) rotation angle of pulley D w/r to the support of A. Follow the rule of signs given in the lecture. Include the necessary FBDs of sections.
Two pipes were connected by a flanged bolt coupling. The material properties are as follows: For outer bolts, 12 pieces, 16 mm diameter, on a mean radius of 150 mm, G = 28 GPa. For the inner bolts, 8 pieces, 12 mm diameter, on a mean radius of 100 mm, G = 20 GPa. Determine the total torque of the system if the shearing stress is limited to 30 MPa in the bolts. (Draw also the FBD) with complete solution
The steel shaft is formed by attaching a hollow shaft to a solid shaft. Determine the maximum torque T (in Nm) that can be applied to the ends of the shaft without exceeding a shear stress of 70034763 Pa and angle of twist of 2.23ᴼ. Use G = 83000000000 Pafor the shaft, x = 2.3 m, and y = 1.89 m. Round off the final answer to two decimal places.Please help me, I only have 30 mins left. TY!
Please help me with this question its urgen
1. The hollow steel shaft (G=12 000000 Psi) must transmit a torque of 300000 Ib-in. The total angle of twist must not exceed 3 degrees per 100 ft. the maximum shearing strength must not exceed 16000 Psi. (a) Find the inside diameter "d" if the outside diameter is equal to 12 inches. (b) Find the maximum torsional shear stress and (c) Find the maximum torsional shear strain.
A steel shaft 2550 mm long must transmit a torque of 34 KN-m. The total angle of twist and the maximum shearing stress must not exceed 3 degree and 110 MPa respectively. Find the diameter of the shaft that meets there conditions. Check based on strength and rigidity. Use G = 78268 MPa. Use two (2) decimal places.
Mechanics Lesson The 6 kN force is in the vertical direction, while the P=7.5 kN force is in the z direction.Since the safe shear stress is 60 MPa, determine the smallest allowable diameter of the AD shaft.
A flanged bolt coupling consists of eight d-mm diameter steel bolts on a bolt circle 263 mm in diameter, and four d-mm diameter steel bolts on a concentric bolt circle 190 mm in diameter. If the torque that can be applied is 9494 Nm without exceeding a shearing stress of 46.89 MPa in the bolts, what is the diameter of the bolts? Round off the final answer to two decimal places.
The mean dimensions of the cross-section of the leading edge and torsion box of an airplane wing can be approximated as shown. If the wing is made of 2014-T6 (G = 19 GPa) aluminum alloy having an allowable shear stress of Tallow = 158 MPa, and the wall thickness is 12 mm. Determine the maximum allowable torque and the corresponding angle of twist per meter length of the wing.
1- The shaft shown in the below Fig. consists of a 75-mm diameter aluminum segment rigidly joined to a 50-mm diameter steel segment. The ends of the shaft are attached to rigid supports. Calculate the maximum shear stress developed in each segment when the torque T = 1130 N.m. is applied. Use G = 28 GPa for aluminum and G = 83 GPa for steel. %3D %3D Aluminum Steel 75 mm diameter 50 mm diameter 1130 N.m Tal 1st 2 m 1 m
100 kip 10 kip ft The 4-in. diameter shaft shown above is made from a ductile brass alloy. Which of the following are closest to the principal stresses in the shaft? 01 = 31.8 ksi 02 = 76.4 ksi = 94.0 ksi 02 = -62.1 ksi O0g - 14.3 ksi 02 = -6.37 ksi Oo= 7.96 ksi 02 = 9.55 ksi