Answered: Question- An uncompacted heap of soil…

Question- An uncompacted heap of soil has a volume of 10,000 m³ and void ratio of 1. If the soil is compacted to a volume of 7500 m³, find the corresponding void ratio of the compacted soil.

Construction Materials, Methods and Techniques (MindTap Course List)

4th Edition

ISBN:9781305086272

Author:William P. Spence, Eva Kultermann

Publisher:William P. Spence, Eva Kultermann

Chapter5: Soils

Section: Chapter Questions

Problem 2RQ: How is the plasticity index of a soil determined?

See similar textbooks

Related questions

Q: The solid shaft is fixed to the support at C and subjected to the torsional loadings and axial load…

Q: 9.79. A concrete conduit of cross-sectional area 10 ft² and wetted perimeter 12 ft carries water at…

A: at 50°Fν=1.410×10-5ft2sso,Re=vDνDh=4×AP=41012=3.33ftRe=83.3331.410×10-5Re=1889362 Flow is turbulant…

Q: Establish the Shear & Moment Equation and Diagram of the loaded beam shown. Consider the Left Body…

Q: The following consecutive staff readings were taken with level and 5m staff at 70 m interval. The…

A: 1- Find elevation of all points by the height of instrument method and apply appropriate check.…

Q: Given are the coordinates of two points P1 and P2. It is required to layout point P2 from an…

Q: A 4-kg sphere is connected to wire ACB through a ring C. The sphere revolves at a constant speed in…

A: The given data is shown below: Mass of sphere=4kgRadius=2.4mα=35°β=45°

Q: The vehicle count obtained in every 10-minute interval of a traffic volume survey done in peak one…

A: given- 10 min time intervalTime interval and vehicle count is given in table

Q: A 500 N force is acting in AB direction. Replace the force with an equivalent force-couple system at…

A: Given:- The magnitude of the force = 500 N The angle = 30° To determine:- Replace the force with…

Q: An axial bar fixed at both ends with no loads applied is subjected to ar increase of temperature.…

Q: Which of the following is NOT TRUE for a state of stress at point for a thin spherical pressure…

Q: An open traverse was run from point A to point B in order to determine the length and direction of a…

Q: 3. The rod OB rotates counterclockwise about O at the constant angular speed of 30 rev/min while the…

A: Given:- V=3ft/sec R= 0.6' w=30rpm=2π60=3.142rad/sec Find Acceleration of collar at A =?

Q: A square column with side dimension of 50 mm rests on top of a timber footing. It is determined that…

Q: A pretimed four-phase signal has critical lane group flow rates for the first three phases of 200,…

A: As per Webster method, optimum cycle time of a signal , Co = 1.5L+51-Y Where L = lost time per…

Q: Replace the force system acting on the pipe assembly by a resultant force FR and couple moment MR,…

A: Given:- The vector form of the force F1 = -25i^-15j^+25k^ lb The vector form of the force F2 =…

Q: A stepped steel shaft shown below is subjected to 10 N-m torque. If the modulus of rigidity is 80…

A: Given: A stepped steel shaft is given,Torque applied, T=10 N-mmodulus of rigidity, G=80 GPa

Q: Consider the following data for concrete with mild exposure Water-cement ratio = 0.50 1010 ITA

A: Given:Water cement ratio, WC=0.5water volume=191.6 litre

Q: A large tank with a nozzle attached contains three immiscible, inviscid fluids as shown. Assuming…

Q: 15. An azimuth observation was taken on Polaris at eastern elongation. The instrument is then turned…

Q: The tank has a square base and is filled with water depth of y= 0.4 m. If the 20-mm-diameter drain…

A: Given:y=0.4 mdiameter of drain pipe, d=20 mm

Q: The cable AB prevents bar OA from rotating clockwise about the pivot O. If the cable tension is 680…

A: The given figure is shown below:

Q: dard temperature20 °C ficient of thermal expansion 11.6*106 of tape is 0.04 kg/m dard tension 60N ed…

A: Temperature correction :CT=LαT-TsCT=198011.6×10-635-20=0.34452m

Q: In figure 2.5, if the pressure of gas in bulb A is 50 cm Hg vacuum and Patm = 76 cm Hg, the height…

Q: 2) The structure as shown supports the horizontal force F = 30 kN. Determine the safe diameter of…

Q: In figure 2.5, if the pressure of gas in bulb A is 50 cm Hg vacuum and Patm = 76 cm Hg, the height…

Q: The section modulus of a rectangula s equal to

A: We know section modulus of section is refferred as :Z=IyI=moment of Inertia y=Neutral axis depth

Q: joining two gradients AB and BC. Hesign the curve at 20 metres intervals. Table Q2 (Units are in 9

A: Length…

Q: nend has 80C certain inst er is observed

Q: It is formed between the horizontal (earth) and the rope a) twisting b) angle of attack c)Incidence…

A: Brief concept introduction- When a rope is placed at an angle to the horizontal surface of the…

Q: 4) A cantilever beam supports a uniformly varying load and a couple as shown in the figure. If EI =…

A: Given data EI = 300.65 KNm2

Q: Solve the force in members DF, DG and CE of the truss shown in the figure using method of joints. 9¹…

A: To Determine Force in the members DF, DG & CE.

Q: The two blocks shown are originally at rest. Block A has a weight of 100 lb and block B has a weight…

Q: Determine the fixed end moments and shears of the beam loaded as shown. Im 2 m 2 kN/m 2m B

Q: An 80-m-long wire of 5-mm diameter is made of a steel with E = 200 GPa and an ultimate tensile…

Q: 4) A cantilever beam supports a uniformly varying load and a couple as shown in the figure. If EI =…

A: Given data EI = 300.65 KNm2

Q: Design the beam for flexure using the maximum moment. Assume b-300mm, h-425mm, cc-40mm,…

Q: TRY THIS ONE ON YOUR OWN!! Assignment 1-F Establish the Shear & Moment Equation and Diagram of the…

Q: A tensile test is conducted on a bar whose cross-section is 12mm thick by 100mm wide. An axial…

Q: The structure as shown supports the horizontal force F = 30 kN. Determine the safe diameter of pin…

A: GIVEN: The structure as shown in the attached figure, supports the horizontal force F = 30 kN. The…

Q: The simple beam with overhang carries a uniform load, w (kN/m) and a force P (kN). (a) Determine the…

Q: ending moment diagrams for the beam shown by the area method and by using cutting a section per…

Q: CE, AT A VELOCITY AT TRANSITION I E, FROM LEADING VER REMAINS I AM

Q: 8.a. Equipment rated at 1200 A or more and more than six feet wide that contains overcurrent…

A: Given data- 8(a) 1200 A rating6 ft or more in width

Q: 3) The simply supported beam with the cross-section as shown supports a total uniformly distributed…

A: Allowable tension flexural stress = 35 MPa Allowable compression flexural stress = 150 MPa

Q: The solid shaft is fixed to the support at C and subjected to the torsional loadings and axial load…

Q: Simple Curve A railway curve is to connect intersecting tangents with the following design data:…

Q: [Select] [Select] m/s [Select] V V (a) the rated velocity in m/s (b) the minimum velocity in (c) the…

A: Given Data: The bank angle of the track is θ=40°. The estimated mass of a car is m=745 kg. The…

Q: An 80-m-long wire of 5-mm diameter is made of a steel with E = 200 GPa and an ultimate tensile…

A: Given that, length of wire, L = 80 m diameter of the wire, d=5 mm Young's modulus E = 200 GPa…

Q: critical element at point A is subjected to the plane stresses component as demonstrated in Figure…

Q: A stainless steel tube with an outside diameter of 60 mm and a wall thickness of 5 mm is used as a…

A: Given :

Concept explainers

Basic Concepts of Water Resource Sustainability

The majority of the earth's surface is composed of water. The water which is available for use by the living beings on earth comes from various water resources. Water resources are the naturally occurring water bodies that are intended to be used by the living beings on earth for drinking and other uses. Water resources provide 3% as freshwater, 97% as saltwater, two-thirds of which are frozen as glaciers and ices. The remaining water which generally doesn't remain frozen are the water resources found underground, precisely known as groundwater. The majority of these water sources act as non-convention sources of power generation, like in hydropower stations.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Basic concepts of water resources sustainability

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

How is the plasticity index of a soil determined?
4. What is the porosity of a soil having a void ratio of 1.234? Round off to two decimal places.
Question 20 What is the porosity of a soil having a void ratio of 1.326? Round off to two decimal places.
Problem 1: For a gravel with D60 0.48mm, D30 0.25mm, and D10 coefficient and the coefficient of gradation. Is it a well-graded or poorly graded soil? - = = = 0.11mm, calculate the uniformity Problem 2: 0.3 mm, D30 The following values for a sand are given: D10 Determine Cu and Cc and state if it is a well-graded or a poorly graded soil. = 0.41 mm, and D60 = = 0.77 mm.
1. Why will bulk density vary between soils but it is valid to use a constant value for particle density (2.65 g cm-3)?
GEOTECHNICAL ENGINEERING: The Undisturbed soil at a given borrow pit is found to have the following parameters. The water content is 15%, the void ratio is 0.60 and the specific gravity of the solids is 2.70. The soil from this borrow pit is to be used to construct a rolled fill having a finished volume of 50,000 yd3 . The soil is excavated by means of a shovel and dumped on trucks. When loaded to capacity these trucks are found to contain, on average, a net weight of wet soil equal to 13,000 lbs. In the construction process, the trucks dump their load on the fill, the material is spread and broken up, after which a sprinkler adds water until the water content is equal to 18%. The soil and water are thoroughly mixed by means of dicers (or other similar equipment) and then compacted until the dry unit weight γd=110 lbs/ft3. Helpful Conversions (3ft=1yd), (γw=62.4 lbs/ft3), (7.48gal/1ft3 ) a) If the fill should become saturated at some time subsequent to construction and does not change…
GEOTECHNICAL ENGINEERING: The Undisturbed soil at a given borrow pit is found to have the following parameters. The water content is 15%, the void ratio is 0.60 and the specific gravity of the solids is 2.70. The soil from this borrow pit is to be used to construct a rolled fill having a finished volume of 50,000 yd3 . The soil is excavated by means of a shovel and dumped on trucks. When loaded to capacity these trucks are found to contain, on average, a net weight of wet soil equal to 13,000 lbs. In the construction process, the trucks dump their load on the fill, the material is spread and broken up, after which a sprinkler adds water until the water content is equal to 18%. The soil and water are thoroughly mixed by means of dicers (or other similar equipment) and then compacted until the dry unit weight γd=110 lbs/ft3. Helpful Conversions (3ft=1yd), (γw=62.4 lbs/ft3), (7.48gal/1ft3 ) a) Assuming that each load is a capacity load, how many truck loads are required to construct the…
4. Specifications require that a fill using borrow soil to be compacted at 95% of its standard proctor maximum dry density. Tests indicate that this maxi- mum is 19.5 kilo Newtons per cubic meter with 12 % moisture. The borrow material has a void ratio of 0.60. Compute the minimum dry and wet unit weight of the compacted soil, compute also the minimum volume of borrow material required to fill 1 cubic meter when compacted. Note: Assume a logical value of Gs with at least 4 significant figures.
Consider a soil that is being placed as a fill and compacted using a sheepsfoot roller (a pieceof construction equipment). Will the action of the roller change the void ratio of the soil?Explain.
What is the porosity of a soil having a void ratio of 1.152?
Q.1. Select the right answer of the following: 1. The void ratio of soil can be: a. greater than void ratio b. less than void ratio c. equal to void ratio d. no one 2. When Gravel had coefficient of uniformity of 3, the soil could be according USCS: a. GW b. GP c. SP d. any one of them 3. In a wet soil mass, air occupies 1/6 of volume and water occupies 1/3 of volume. The void ratio is: a. 0.25 b. 0.50 4. For the soil with LL= 45%, PL = 25% and water content = 15% the liquidity index is: B.0 с. 1.50 d. 1.00 a.0.6 5. The type of unit weight of soil s depends on: с. 1 dinone of them а. е b. n c. YW d. S 6. Soil has LL of 30, the corresponding plasticity index given by A-line: a. 7.3 b. 7.5 c. 9.0 d. 9.5 7. The porosity in of soil is function of: c. Vv & n P.= L.L-PL 12:45-25=2 a. Vv&Vs b. Vv& Vt d. Vs & n 8. For a soil deposit having n= 33% and G 2.6, ysaturated= 15KN/m3, S is: %3D а. 1.0 b. 1.05 с. 1.07 d. 1.10 10. When saturation in soil sample occurs, the degree of saturation: a.…
The Undisturbed soil at a given borrow pit is found to have the following parameters. The water content is 15%, the void ratio is 0.60 and the specific gravity of the solids is 2.70.The soil from this borrow pit is to be used to construct a rolled fill having a finished volume of 50,000 yd3. The soil is excavated by means of a shovel and dumped on trucks. When loaded to capacity these trucks are found to contain, on average, a net weight of wet soil equal to 13,000 lbs.In the construction process, the trucks dump their load on the fill, the material is spread and broken up, after which a sprinkler adds water until the water content is equal to 18%. The soil and water are thoroughly mixed by means of dicers (or other similar equipment) and then compacted until the dry unit weight γd=110 lbs/ft3 Helpful Conversions (3ft=1yd), (γw=62.4 lbs/ft3), (7.48gal/1ft3) a) Assuming that each load is a capacity load, how many truck loads are required to construct the fill?b) What is the volume in…