QUESTION 9 A vertical curve is needed to join to tangents; G₁=2% and G2-5%. Assuming the worst case scenario for braking, and the AASHTO recommended values for deceleration and perception-reaction time, calculate the minimum length of curve (ft) needed to satisfy the safety criteria. The design speed is 50 mph.

QUESTION 9 A vertical curve is needed to join to tangents; G₁=2% and G2-5%. Assuming the worst case scenario for braking, and the AASHTO recommended values for deceleration and perception-reaction time, calculate the minimum length of curve (ft) needed to satisfy the safety criteria. The design speed is 50 mph.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the minimum length of a sag vertical curve if the grades are -3.5% and +3%. Design speed is 60 mi/h. State assumptions used. Consider the following criteria: stopping sight distance, comfort, and general appearance.
Q1/ Figure below illustrates a compound curve, if the intersection angle between two tangents is equal to (110°), and the intersection angle is (24°59') for the first simple curve (A). And the tangent is equal to (250 ft) for the second simple curve (B).determine The deflection angles and the chord lengths for setting out the curve at whole stations from PC to PT (for second simple curve (B) only) if the station at point (g) is equal to (287+00), and the distance between station (r) and PCC is equal to (30 ft). 110° РСС tR = 250 ft A В \24°59)
An equal-tangent vertical curve connects a +3.2 % and a -1.1 % grade. The PVI is at station 100+20 and elevation 950 ft and the PVT is at station 105+20. Answer the following 5 questions Question 3 to Question 7. The station of the PVC is at: sta 93+20 sta 95+20 sta 97+20 sta 99+20 sta 105+20
Design a vertical curve (i.e., Determine length of the curve as well as station and elevation of the vertical curve's PVC and PVT) with the given PVI (station and elevation given the figure below) to go through a future intersection location at the point at which the vertical curve is flat. Report the vertical curve's design speed to the nearest 5 miles per hour. PVC Future Intersection Station = 100+00 G1 = -2.6% PVT PVI G2 = 1.0% Station = 99+00 Elevation = 228 ft %3|
Please show complete solutions and box the final answers
QUESTION 3 A vertical curve is needed to join to tangents; G₁-5% and G₂-2%. Assuming the worst case scenario for braking, and the AASHTO recommended values for deceleration and perception-reaction time, calculate the minimum length of curve (ft) needed to satisfy the safety criteria. The design speed is 50 mph.
A curve of 100 m radius (e=8.0 % and fs=0.14) is located at a section of an existing rural highway which restricts the safe speed to 55 % of the design speed causing a high accident rate. To reduce the accident rate, a new curve is to be designed. Determine the minimum radius of this curve if the safe speed should be increased to the design speed. Assume the same values of e and fs.
this is one question split by parts a and b.
Question- If design velocity on the curve is 100 kmph then find the design super elevation on a 4 degree horizontal curve for narrow gauge track.
A+1 percent grade intersects with a-2 percent grade at station (535+ 24.25) at an elevation of 300 t. (a) if the design speed is 65 mi/h, determine the minimum length (in t) of vertical curve using the rate of vertical curvature. (Assume the stopping sight distance is less than the length of the curve.) it (b) Using the length found in part (a), find the stations and elevations (in R) of the BVC and EVC and the elevation (in t) of each 100 t station. (In the table below, the first row corresponds to the BVC and the last row corresponds to the EVC. Round your elevations to at least one decimal place.) Station Elevation (t) 533 + 00 534 + 00 535 + 00 536 + 00 537 + 00 538 + 00 (c) Using the length found in part (a), find the station and elevation (in t) of the highpoint. station nlevation
A vertical curve is needed to join to tangents; G1=1% and G2=4%. Assuming a level grade (0%) for braking, and the AASHTO recommended values for deceleration and perception-reaction time, calculate the minimum length of curve (ft) needed to satisfy the safety criteria. The design speed is 60 mph.
A vertical curve is needed to join to tangents; G₁=1% and G2-4%. Assuming a level grade (0%) for braking, and the AASHTO recommended values for deceleration and perception-reaction time, calculate the minimum length of curve (ft) needed to satisfy the safety criteria. The design speed is 60 mph. Response Feedback: G2-G₁ is positive, therefore a sag curve. A=3 SSD(0%)=565.5 ft If you assume SL, Lmin-340 ft. SSD is greater than Lmin. The assumption is good.