Question 9 A second calibration standard solution of an iron(II) salicylate complex was prepared in two steps. First, 10.0 mL of a 0.100 M stock solution was added to 90.0 mL of solvent to make 100.0 ml. of the first calibration standard solution and, secondly, 80 mL of that first calibration solution plus 20.0 mL of solvent were mixed to make the second calibration standard. What is the concentration of the second calibration standard solution? (A) 100 mM B) 59 mM 0,14 mM 80 mM 8.0 mM

Question 9 A second calibration standard solution of an iron(II) salicylate complex was prepared in two steps. First, 10.0 mL of a 0.100 M stock solution was added to 90.0 mL of solvent to make 100.0 ml. of the first calibration standard solution and, secondly, 80 mL of that first calibration solution plus 20.0 mL of solvent were mixed to make the second calibration standard. What is the concentration of the second calibration standard solution? (A) 100 mM B) 59 mM 0,14 mM 80 mM 8.0 mM

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

analytical chemistry, please solve question 21- Calculate the silver ion concentration in terms of pAg during the titration of 50.00 mL of 0.05000 M Nal with 0.1000 M AgNO, after the addition of 25.0 mL of AgNO, Ksp for Agl-8.3x107 a) 8.04 b) 9.71 c) 5.69 d) 3.88 e) 7.16
At equivalence ____ ml titration was delivered Ph of mid point is____ Analyte is _____ Best indicator is ___
Which rapid and quantitative analysis requires a sample solution of metal ion to be titrated against a standard solution of EDTA, in the presence of a buffer?* Alkalimetric Replacement Back Titration Direct Which agent is added into a solution if direct titration is deemed to proceed slowly?* Indicator Titrant Catalyst Demasking agent Which method uses an excess solution of EDTA added to a sample and then pH is adjusted for back titration with a metal ion solution?* Replacement Residual Alkalimetric Direct Which reagent will form a more stable complex with interfering ions rather than the with the indicator and EDTA?* Masking agents Demasking agents Chelating agents Complex agents Which of the following contains a set of incorrectly paired words?* Chelatometry - Complexation / Precipitimetry - Argentometric…
Can a conventional pH meter with conventional buffer solutions measure the pH of the mobile phase typically used in HILIC? Explain
The answer to the previous question I calculated was 0.0324 M of the standard Ca solution and now I'm not sure what I'm doing wrong in my calculations for the next problem. 2. "For each of the calcium standard titrations, determine the exact concentration (M) of the EDTA solution, using the concentration of the standard Ca solution you calculated in 1. Find an average of the calculated concentrations." My volumes for the titrations were: Ca volume used in titration 1 = 10.00 mL and for the second titration = 9.98 mL Ca used EDTA volume used in titration 1 = 16.98 mL and for the second titration = 17.00 mL EDTA used
1. Calcium is determined in serum by microtitration with EDTA. A 150 ml sample is treated with few drops of 2M KOH, calmagite indicator is added and the titration is performed with 0.00125M EDTA, using a microburet. A 0.205mL of EDTA is required for titration. What is the level of Ca in the serum in a. mg/dL b. mg/L
Comparing the two quantities based on the given condition, which is greater I or II? or are they equal? can the quantities be measured? Consider the analysis of Fe in ore using permanganate as titrant. Under the same acidic conditions I. % Fe with pre-reduction II. % Fe without pre-reduction
Titration of a weak acid with a strong base: (acetic acid, NaOH): ChemCollective: http://www.chemcollective.org/ Materials needed: 1 M acetic acid, 1M NaOH, 250 mL Erlenmeyer flask, buret, phenolphthalein indicator. 1. Choose 1 M acetic acid and 1 M NaOH solution from stock solutions. 2. Transfer 25.0 mL of acetic acid to a 250 mL Erlenmeyer flask, write down the pH value in your table in observation #1. Add 0.3 mL of Phenolphthalein indicator to the flask. Duplicate this solution. Use one of the two solutions to do titration. 3. Transfer 50.0 mL of NaOH solution to a buret Titration: Transfer 5.0 mL of NaOH solution from the buret at a time to the flask containing 25.0 mL of acetic acid solution (one of the duplicate solutions) until you have added a total of 20.0 mL, then add 1.0 mL at a time until you have added a total of 24.0 mL of NaOH. Then add 0.2 mL at a time to reach 25.0 mL of NaOHà note down the observed pH value after each addition. Keep adding 1.0 mL of NaOH at a time…
A 340.00 mL solution of 0.00175 M AB2 is added to a 140.00 mL solution of 0.00235 M CD4. What is pQsp for AD2?
DATA AND RESULTS: Titration Data (Standardization of EDTA) Example II Mass, g Caco, 0.0250 0.0251 0.0246 0.0254 Final reading, mL 25.00 24.91 24.87 25.31 Initial Reading, mL 0.00 0.02 0.02 0.02 Volume, mL EDTA 25.00 Molarity of EDTA, M 0.009992 B. Analysis Data Example II Volume of Sample, mL 25.00 24.90 25.10 25.0 Final reading, mL 27.46 25.08 25.06 24.99 Initial Reading, mL 0.00 0.02 0.02 0.02 Volume of EDTA, mL 27.46 Molarity of EDTA, M 0.009992 Ca" concentration, ppm 440 STATISTICAL EVALUATION OF RESULTS Standardization of EDTA Mean, M EDTA Median, M EDTA Standard Deviation Ci for u at 95% Prob. Level Reported value: M EDTA Ca" Concentration Mean, Ca" ppm Median, Ca" ppm Standard deviation Cl for u at 95% Prob. Level Reported value: Ca" ppm
41 and 42
Is data correct?