QUESTION 8 Refer to the voltage divider system of Figure 7. Given ß = 120. %3D i. Compute the value of re. i. Draw the ac equivalent circuit for the network of Figure 7 ii. Express input impedance, Z¡ and output impedance, Zo. iv. Determine the voltage gain, Av= Vout/Vin. Vcc 18 V 3.3 kn R, Co 18 kn o Vo C, 1 µF 1 μΕ R2 RE 4.7 kn 1.2 kn Figure 7

QUESTION 8 Refer to the voltage divider system of Figure 7. Given ß = 120. %3D i. Compute the value of re. i. Draw the ac equivalent circuit for the network of Figure 7 ii. Express input impedance, Z¡ and output impedance, Zo. iv. Determine the voltage gain, Av= Vout/Vin. Vcc 18 V 3.3 kn R, Co 18 kn o Vo C, 1 µF 1 μΕ R2 RE 4.7 kn 1.2 kn Figure 7

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Circuit diagram of HWR (without Capacitor): MA Circuit diagram of HWR (with Capacitor):
In general, the greater the absolute value of the impedance in a circuit:A. The greater the flow of alternating current.B. The less the flow of alternating current.C. The larger the reactance.D. The larger the resistance.
6. The main difference between resistance R and capacitive reactance X, is that (a) Xc is the same for both DC and AC signals, where R depends on frequency of the AC signal (b) R is the same for both DC and AC signals, where X depends on the frequency of an AC signal (c) R is measured in ohms and X is measured in farads (d) None of the above
QUESTION 1 An 850nF capacitor and a resistor are connected in series with a function generator. If the supply voltage is 100VZ-34.7 at 1kHz, find the total impedance of the circuit. O 1.5kOL-34.7* O 820042.8 3300L-34.7 O 2kn2-25.7"
1) Two identical voltage waveforms of difference phase angles are shown in Figure B. Write down the expression of waveforms A and B clearly. HUS Voltage (V) 8 0 K/N B 7: ST ot
6. Figure 3 shows a series RLC circuit. R8 L1 100mH 240V 50Hz Figure 3: Series RLC circuit 100 (a) Draw the phasor diagram for the circuit. (b) Calculate the impedance of the circuit. (c) Calculate the supply current. (d) Calculate the voltage across each component. C1 47uF
If a circuit has a resistance of 3002 and a series inductance of 5002, what is the relationship between the applied circuit voltage and the circuit current? The applied voltage lags the circuit current. The phase shift between the circuit voltage and current changes with time. The applied voltage is in phase with the circuit current. The applied voltage leads the circuit cur Previous Page Next Page Page 2 of 10
A 43mH coil in series with a 1200 ohm resistor across a sine wave ac voltage source with a frequency of 6 kHz. The total impedance for the circuit is O 1620 46.5° ohm esc 2017 53.5° ohm 1200 53.5° ohm 2820 46.5° ohm ! 1 Q ← 2 W #3 C E $ 54 R G Search or type URL % 5 MacBook Pro T A 6 Y & 7 ☆ U * 8 + 1 ( 9 ( 0 ) 0 4) P + O = [ delete
If the measured values of R1 = 323.1 Q, R2 = 324.2 Q and R3 = 324.7 Q, calculate the difference in measured R compared to your calculation of equivalent R in Ohms? KIT NO. 1PASCO EM-8622 SCIentfic CYRCUIT EXPERIMENT TENMA 72-7780 1079 A C Auto Range 6000 Counte True RMS Multimeter ANGE MAX/MIN RELA Hz/% DILIGHT SELECTIVR.C Hz% mA H Am Hz% ONCV 60A. CE A (10mviA) VOHZC ww COM FUSED FUB RI
6. Figure 3 shows a series RLC circuit. C1 R8 LI 100 100mH 47uF 240V 50HZ Figure 3: Series RLC circuit (a) Draw the phasor diagram for the circuit. (b) Calculate the impedance of the circuit. (c) Calculate the supply current. (d) Calculate the voltage across each component.
For the series circuits of the figure below, calculate the total impedance (ZT). R1 4 k2 XL1=4 k2 ZT Xei= 6 k2 Xc2= 3 k2 XL2= 4 k2 Z7= 17.4 kn, the angle is 76.7° Ob. Z7= 17.4 kn, the angle is 56.3° .Oc. Z7= 4.1 kn the angle is -14° Od. Z7= 7.2 kn the angle is 56.3°
A2 KO resistor and 30 mH inductor are connected in series, across a 120 V A.C power source oscillating at 60 Hz frequency .Calculate i) The current in the circuit i) The voltage drop across the resistor & inductor ii) The power dissipated in the circuit. iv) The apparent power & reactive power in the circuit. v) Draw the phasor diagram.