Question 3To reduce the power consumption, the capacitorsCompleteshould be locatedMarked out of1.00O a. As far as possible to the loadP Flag questionb. Not suitable placeO c. As close as possible to the loadd. Not too close not too far from the loadQuestion 4A load 200+j0 ohms is connected across a 250 V andComplete50 Hz supply. Find the reactive power.Marked out of1.00O a. 350 VARP Flag questionO b. 360 VARO C. zero VAROd. 420 VAR

Answer 3: Locating capacitor as close as possible to the Load end will help to reduce losses within…

Question 3 To reduce the power consumption, the capacitors should be located Complete Marked out of 1.00 O a. As far as possible to the load P Flag question b. Not suitable place O C. As close as possible to the load O d. Not too close not too far from the load Question 4 A load 200+j0 ohms is connected across a 250 V and 50 Hz supply. Find the reactive power. Complete Marked out of 1.00 a. 350 VAR P Flag question O b. 360 VAR C. zero VAR d. 420 VAR

Question 3 To reduce the power consumption, the capacitors should be located Complete Marked out of 1.00 O a. As far as possible to the load P Flag question b. Not suitable place O C. As close as possible to the load O d. Not too close not too far from the load Question 4 A load 200+j0 ohms is connected across a 250 V and 50 Hz supply. Find the reactive power. Complete Marked out of 1.00 a. 350 VAR P Flag question O b. 360 VAR C. zero VAR d. 420 VAR

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1
Question 6/12 Using source transformation, if V, 60V them v,is 1. OA 2. OB 3. OC 4. OD 5. OE 6. OF 7. OG 8. OH 32 ww ww 42 3 A ( 82 Vx A) 3.2V B) 9 €V C) 16V D) 22.4V E) 28.8V F1 352V G) 41.6V AB+ (H Previous Next
Problem (Homework): A single phase full wave AC voltage controller supplies a resistive load. The input RMS voltage is 120V at 60Hz. Determine the output RMS voltage when a is 0°, 90°, and 180º.
The voltmeters in the figure measure RMS voltages. If V1 = 13 V and V2 = 8.5V what is V3? C R V V2 V3 O 15.53 V O 4.5 V O 21.5 V O 8.5 V О 13V
A step down converter is operated with a duty cycle of k 0.75. The input voltage is V, 20V. and the load is L=5mH, R=152 The minimum inductor current is I 0.1A. The maximum inductor current is %3D %3D Select one: O a. 0.9 A O b. 1.9 A O C. None of these O d. 1.1 A O e.2A
The voltage applied to the metal grid of CRO is negative with respect to cathode. Select one: O True O False The sinusoidal current waveform having the maximum value of 30 A. then the R.M.S value is Three coils each having resistance of 29 0 are connected in star across 436 V. 50 Hz supply. Then the total power consumed is O 19665.10 W O 3784.66 W O 755.20 W O 226.05 W
Show the voltage waveforms across each half of the secondary winding and across RL. Find the average value of the full-wave rectified voltage in Figure. 120 Vrms elller 4:1 reetee D₁ RL 1.0 ΚΩ
Assuming the capacitors in Figure 12-2 are non-polarized electrolytic capacitors, what is the maximum AC rms voltage that can safely be applied to the circuit? total capacitance 24 V O 35 V O 100 V O 49.5 V 10V²=474²=186 € uF 50 V uF 35 Figure 12-2 33
Measure the voltage and current across the capacitor.Measure the average power delivered by the source.Observe the phase angle in the condenser
The hypotenuse side of the power triangle is equal to Reactive power Active power Apparent power True power
3. Sketch the current waveform for the circuit in Figure below. The diac has a breakover potential of 20 V. IH = 20 mA. 25 V rms R 1.0 ΚΩ
Prove that the fluctuation of voltage at the load end is largely a function of the reactive power, and the fluctuation system frequency is a function of the active power flow