Question 7 The data from a falling head test is shown. Diameter of standpipe: 3 cm. Initial Head: 93.34 cm. Duration of test: 16 min. Length of soil sample: 33.43 cm. Diameter of permeameter: 43 cm. If the soil permeability is 0.0054 cm/min, determine the final head (in cm.) of the permeability test. Round off to two decimal places.

Question 7 The data from a falling head test is shown. Diameter of standpipe: 3 cm. Initial Head: 93.34 cm. Duration of test: 16 min. Length of soil sample: 33.43 cm. Diameter of permeameter: 43 cm. If the soil permeability is 0.0054 cm/min, determine the final head (in cm.) of the permeability test. Round off to two decimal places.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

P2, 4.3 List the given, required, graph and box the final answer.
In a falling head permeability test, the following data was obtained: diameter of standpipe = 1.5 cm; diameter of sample = 10.16 cm; height of water level at beginning of test (h1) = 30 cm; length of sample (L) = 20 cm. The soil had a coefficient of permeability (k) equal to 3.4 x 10°cm/sec. If the test was conducted for a period of 8 hours, what was the water level at the end of the test (h2)? %3D Time when water level is at h, is t, (t,) a = area of standpipe Time when level is at 19% h, is t2 (t2) A = cross-sectional area of soil sample Soil sample
A dry soil sample has the total mass (kg) shown in the table below. Use the data provided to complete the MVR table and determine the engineering parameters listed below. Write all answers for the mass/volume table to three decimal places and write all the answers for the engineering parameters (w, n. PT.PD. YT.& YD) as real numbers only (i.e. no %) to two decimal places. Be consistent with the units provided but do not include the units in your answer. VOLUME Va = Blank 1 m³ Vw = Blank 2 m³ Vs = Blank 4 m³ V₁ = Blank 6 m³ void ratio = 0.45 water content = Blank 7 porosity = Blank 8 Total density (kg/m3) = Blank 9 Dry density (kg/m3) = Blank 10 Total unit weight (kN/m3) = Blank 11 Dry unit weight (kN/m3) = Blank 12 AIR WATER p=1000 kg/m³ SOLIDS R.D. = 2.70 MASS Ma = 0 kg Mw = Blank 3 kg Ms = Blank 5 kg MT= 452.650 kg
76 .ll Q3.png The data from standard and modified proctor test on a soil sample (density of solids: 2680 kg/m3 ) are provided below: Standard proctor test Modified proctor test Dry density (kg/m) 1691 Dry density (kg/m') 1873 Water content (%) Water content (%) 9.3 9.3 1715 11,8 1910 12.8 1755 14.3 1803 15.5 1747 17.6 1699 18.7 1685 20.8 1641 21.1 1619 23 a) Plot the compaction curves (both standard and modified in one graph). b) Establish the maximum dry density and optimum water content for each test.
K1
need asap pleaseeee
The attached figure shows the soil sample prepared and setup for constant head permeability test. If the permeability of the soil is 4.5 x 10-3 cm/sec, what is the required time to collect 100 ml of outflow water under the steady state condition? 40 cm Soil in the pipe with internal diameter 20 cm Outflow collection 50 cm 40⁰ 90 cm -Datum- 10 cm
35 The data from a falling head test is shown. Diameter of standpipe: 6 cm. Initial Head: 90.97 cm. Duration of test: 17 min. Length of soil sample: 30.68 cm. Diameter of permeameter: 40 cm. If the soil permeability is 0.0089 cm/min, detemine the final head (in cm.) of the permeability test. Round off to two decimal places.
1. A series of Atterberg limit tests was performed on samples of a gray-brown silty clay. The table below summarizes the results of four liquid limit tests. Using this data, Trial Number Number of blows Weight of wet sample + container (g) Weight of dry sample + container (g) Weight of container (g) 15.61 16.82 16.34 a. Determine the flow curve for the soil (graph and show the equation of the best fit line) b. Determine the flow index for the soil 1 23 2 36 3 26 15.12 4 c. Calculate the liquid limit d. Calculate the plasticity index Plastic limit tests show an average of 38.5%. 23.50 26.94 26.86 26.27 21 19.89 22.10 22.59 21.96
What is the 95% maximum dry density from the laboratory (Please answer in two decimal places in Mg/m3)? (You may do a simple sketching to assist your answer). Please answer value only | Ya(Mg/m³) w % 1.62 1.66 1.72 1.70 1.63 1.57 12.4 13.3 15.5 17.4 18.3 20.1 Laboratory compaction tests results of a soil fill compacted Site A are: Table A
A permeability test was conducted on a saturated sample of coarse soil. The soil specimen has a 170 mm diameter and a length of 300 mm. hi and hz was 800 mm and 300 mm respectively. The permeabili this sample in cm/sec is 3.96 10 Time required to collect a volume equal to 350 cm at 20°C is: Select one: 4 min 5 min 4 sec 5 sec ge Teo