In the falling head permeability test, in duration of 4 hours the initial head of 950 mm is dropped to 300 mm. The diameter of the stand pipe is 0.6 cm. The length and diameter of the soil specimen are 20 cm and 10 cm respectively. What is the coefficient of permeability (mm/s) of the soil?

In the falling head permeability test, in duration of 4 hours the initial head of 950 mm is dropped to 300 mm. The diameter of the stand pipe is 0.6 cm. The length and diameter of the soil specimen are 20 cm and 10 cm respectively. What is the coefficient of permeability (mm/s) of the soil?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: constant head permeability test is performed on soil that is 2 cm x 2 cm square, and 2.5cm long. The…

Q: A falling-head permeability test was conducted on a soil that is classified SM. The diameter and…

Q: A fine-grained (silty-clay) soil is required for the core of a rockfill dam. The permeability tests…

A: The diameter of the specimen is 8 cm.The length (L) is 15 cm.The below table shows the test data of…

Q: FUNDAMENTALS OF GEOTECHNICAL ANALYSIS A constant head permeability test is performed on soil that…

Q: A constant=head test was conducted on a sample of soil 15 cm long and 60 cm? in cross-sectional…

A: The given data is: Length of sample (L) = 15 cm Area of the sample (A) = 60 cm2 Quantity of water…

Q: A permeability test is inducted with a sample of soil that is 60 mm in diameter and 120 mm long .…

Q: k₂ for 10 seconds and the water level is 20 cm, the water flowing measured as much as 50 cm3. What…

Q: A fine sand was tested in situ to give a coefficient of permeability of 3.7 x107 m/s. A sample of…

A: The objective of the question is to determine whether the in situ testing was reflected by the…

Q: 1. For a constant head laboratory permeability test on a dine sand, the following values are given:…

Concept explainers

Laboratory Determination of Hydraulic Conductivity

Hydraulic conductivity is the measure of flowability of water inside the soil in the presence of a hydraulic gradient. The hydraulic gradient is defined as the difference in the water heads in the soil, which induces a water motion. In simple terms, a hydraulic gradient is the presence of a potential that induces a flow of water.

Question

In the falling head permeability test, in
duration of 4 hours the initial head of 950 mm
is dropped to 300 mm. The diameter of the
stand pipe is 0.6 cm. The length and diameter
of the soil specimen are 20 cm and
10 cm respectively. What is the coefficient of
permeability (mm/s) of the soil?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given information

VIEW

Step 2: Find coefficient of permeability

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Laboratory determination of hydraulic conductivity

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A constant head permeability test is performed on soil that is 4 cm2, and 2.5cm long. The head difference applied during the test is 20 cm and 7 cm3 is collected over a time of 100 sec. Then, falling head test is conducted on the same soil specimen at the same time (t1 – t2 = 100 sec), and the standpipe diameter is 0.8 cm. If the average head during the test should be 18 cm, what are h1 and h2 values, provide step by step solution solving h1 and h2 values.
A constant head permeability test is performed on soil that is 4 cm2, and 2.5cm long. The head difference applied during the test is 20 cm and 7 cm3 is collected over a time of 100 sec. Provide step by step solution. What is the permeability based on these test conditions and results.
1. During Atterberg limit tests in the soil mechanics laboratory, the students obtained the following results from a clayey soil. Liquid limit tests: Number of Moisture blows, N content (%) 14 38.4 16 36.5 20 33.1 28 270 Plastic limit tests: Students conducted two trials and found that PL = 172% for the first trial and PL = 17.8% for the second trial. a. Draw the flow curve and obtain the liquid limit. b. What is the plasticity index of the soil? Use an average value of PL from the two plastic limit trails.
I will upvote for correct answer
Problem: For a constant laboratory permeability test on a fine sand, the following data are given: Length of specimen - 16 cm Diameter of specimen - 9.6 cm Constant head difference - 50 cm Volume of water collected in 4 min - 420 cc Void ratio of the soil specimen - 0.55 A.) Determine the hydraulic conductivity of the soil in cm/sec B.) Determine the discharge velocity in cm/sec C.) Determine seepage velocity in cm/sec
In a constant head permeability test in the laboratory as shown in Figure Q2(e), the data is recorded in Table Q2(b). The void ratio of the soil specimen is 0.46. Determine; (i) Hydraulic conductivity, k, of the soil in cm/sec. (ii) Discharge velocity in cm/sec.
A sample of sand is subjected to a constant head permeability test. The sample diameter is 60 mm and its length is 130 mm. Under an applied head of 60 cm, 119 cm³ of water flows through the sample in 5 minutes. Determine (a) the coefficient of permeability, and (b) the discharge velocity.
Solve !
Problem: For a constant laboratory permeability test on a fine sand, the following data are given: Length of specimen - 16 cm Diameter of specimen - 9.6 cm Constant head difference - 50 cm Volume of water collected in 4 min - 420 cc Void ratio of the soil specimen - 0.55 A.) Determine the hydraulic conductivity of the soil in cm/sec B.) Determine the discharge velocity in cm/sec C.) Determine seepage velocity in cm/sec Problem: For a falling head permeability test, the following are given: Length of Soil Specimen - 200mm Area of Soil Specimen - 1000mm^2 Area of Stand pipe - 40mm^2 Head Difference at time t = 0 min - 500mm Head Difference at time t = 3 min - 300mm A.) Compute hydraulic conductivity of the soil in cm/sec B.) Compute the seepage velocity if the porosity is 0.25 in cm/sec C.) What is the head difference at time t = 100 sec in mm