Question 6A sluice gate is commonly used in irrigation systems, which controls flow rate in a channel by simplyraising or lowering a vertical plate. A force is exerted on the gate due to the difference between the waterheights Y, and Y, and the flow velocities Vị and Vz upstream and downstream from the gate respectively.Disregarding the wall shear forces at the channel surfaces, develop relations for V1, V2 and the force actingon a sluice gate of width W during steady and uniform flow.Sluicegate

Name: Question 6A sluice gate is commonly used in irrigation systems, which
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: Question 6A sluice gate is commonly used in irrigation systems, which controls flow rate in a channel by simplyraising or lowering a vertical plate. A force is exerted on the gate due to the difference between the waterheights Y, and Y, and the flow

Engineering

Mechanical Engineering

Question 6 A sluice gate is commonly used in irrigation systems, which controls flow rate in a channel by simply raising or lowering a vertical plate. A force is exerted on the gate due to the difference between the water heights Y, and Y2 and the flow velocities Vị and Vz upstream and downstream from the gate respectively. Disregarding the wall shear forces at the channel surfaces, develop relations for V1, V: and the force acting on a sluice gate of width W during steady and uniform flow. Sluice gate

Question 6 A sluice gate is commonly used in irrigation systems, which controls flow rate in a channel by simply raising or lowering a vertical plate. A force is exerted on the gate due to the difference between the water heights Y, and Y2 and the flow velocities Vị and Vz upstream and downstream from the gate respectively. Disregarding the wall shear forces at the channel surfaces, develop relations for V1, V: and the force acting on a sluice gate of width W during steady and uniform flow. Sluice gate

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Help with this practice question
Use density of water = 1000kg/m^3 and acceleration due to gravity equal to 9.81m/s^2. A rectangular tank containing water at a depth of 1.2m is accelerating towards the right, the motion of which is parallel to the longest side. If the tank has the following dimensions: length = 3 meters, width = 1.8 meters, and height = 1.5 meters, determine the following: the maximum allowable acceleration (m/s^2) of the tank; and the unbalanced force causing the maximum acceleration in kN. angle (in degrees) of fluid inclination of the acceleration from part a. how many cu.m of water is spilled when a = 2.5m/s^2. Note: Do not include units in your answers. Do not round off intermediate values and answer in four decimal places.
Water flows steadily through a horizontal 30 degree pipe bend. At the inlet point 1, the diameter is 0.3 m, the velocity is 12 m/s, and the pressure is 128 kPa gauge. At the outlet point 2, the diameter is 0.38 m and the pressure is 145 kPa gauge. Determine the forces F_x and F_y necessary to hold the pipe stationary.
Q2) Several water pipes intersect at the junction box illustrated in Figure. Determine the force required to keep the junction box in place. Assume water at 4°C. 250 mm Q₁ = 0.2 m³/s P₁ = 480 kPa 350 mm 300 mm QIVA = 0.3 m³/s /P = 400 kPa 30° Q=0.1 m³/s Pc = 450 kPa 50⁰ 200 mm 60° Q = 0.4 m³/s PD = 350 kPa
A pipeline of 50 mm diameter and 4.5 km length connects two reservoirs whose constant difference of water level is 12 m. A branch pipe 1.25 km long and taken from a point distance of 1.5 km from reservoir A, leads to reservoir C whose water level is 15 m below that of reservoir A. Find the diameter of the branch pipe so that the flow into both the reservoirs is the same. Assume the coefficient of friction for each pipe, f = 0.0075, and neglect minor losses.
A boat having a mass of 80 Mg rests on the bottom of the lake and displaces 11.75 m^3 of water. Since the lifting capacity of the crane is only F = 550 kN, two balloons are attached to the sides of the boat and filled with air. The volume of a sphere is V =4/3πr^3. ρw = 1000 kg/m^3.Determine the smallest radius r of each spherical balloon that is needed to lift the boat. Neglect the mass of air and of the balloon for the calculation required for the lift and What is the mass of air in each balloon if the air and water temperature is 12∘C? The balloons are at an average depth of 20 mm. The gas constant for air is R= 286.9 J/(kg⋅K)
Water flows through a pipe AB of diameter d1= 60mm, which is in series with a pipe BC of diameter d2= 85mm in which the mean velocity V2 = 3m/s. At C the pipe forks and one branch CD is of diameter d3 such that the mean velocity V3 is 2.5 m/s. The other branch CE is of diameter d4= 40mm and conditions are such that the discharge Q2 from BC divides so that Q4= ½ Q3. Determine Q1, Q3, Q4 and d3.
The tank shown drains through a triangular weir whose flowrate is described by the equation given. Determine the time it will take for the tank to drain from completely full (h = 5 ft) to 5.25 feet deep (h = 0.25 ft) assuming there is no flow into the tank. Volumetric Flowrate h=5 ft + 5 ft 3 ft³ S = 2.48 h².5 (for h in feet) 10 ft -20 ft- -20 ft-
Water ( density 1000kg/m3) flows downward naturally through a vertical pipeline of diameter D=25 cm and length L= 100 m . Determine the pressure gradient causing flow ( USE π = 3 ; g = 10 m2/s ) ANSWER: 10 kPa/m (Although I wrote this is the answer under the question in some of the questions I posted before. Different answers were found from the answer. The exact answer to this question is 10kPa / m.)
None