Question 6(a) A parallel network consists of two branches A and B. Branch A has a resistance of 10Q and an inductance of 0.1 H in series. Branch B has a resistance of 20 Q and acapacitance of 100 µF in series. The network is connected to a single-phase supply of 230V at 50 Hz. Calculate the magnitude and phase angle of the current taken from theKyddnsMajor Topic 1Single-phase 1(b) Draw and explain the transistor tree diagram.Major Topic 4Transistor(c) Calculate the resistance and inductance or capacitance in series for each of thefollowing impedances, assuming the frequency to be 50 Hz:(a) 50+j30 2;(b) 30-j50 2;U.0970Major Topic 13CRImpedance circuits

V=230Vf=50HzBranch-A:Resistor '10Ω' in series with inductor '0.1H'.Branch-B:Resistor '20Ω' in…

Question 6 (a) A parallel network consists of two branches A and B. Branch A has a resistance of 10 Q and an inductance of 0.1 H in series. Branch B has a resistance of 20 and a capacitance of 100 µF in series. The network is connected to a single-phase supply of 230 V at 50 Hz. Calculate the magnitude and phase angle of the current taken from the supply.

Question 6 (a) A parallel network consists of two branches A and B. Branch A has a resistance of 10 Q and an inductance of 0.1 H in series. Branch B has a resistance of 20 and a capacitance of 100 µF in series. The network is connected to a single-phase supply of 230 V at 50 Hz. Calculate the magnitude and phase angle of the current taken from the supply.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A series circuit consisting of 17ohm resistance and 20mH inductane is connected across a 220V(RMS) 60Hz supply. Determine the magnitude of the total current in the circuit.
A capacitance is rated 100 kVar, 380 volts, 50 hz. What will its rating be at 60 Hz 220 V?
Inductors of 1 H and 2 H are connected in series to a 440-V, 60-Hz power supply. Determine the total current flow for the circuit. Repeat for the two inductors connected in parallel to the power supply.
A utility company plans to connect a total of 20 mF of capacitance to a 7200-V line. To make this connection, four capacitors will be connected in series. What is the total current flow through the circuit?
1. A resistor of 2502, is connected in series with a 1.5 H inductor, cross a 100 V, 50 Hz supply. Çalculate (a) the current flowing, (b) the circuit phase angle, (c) the p.d. developed across each component and (d) the power dissipated.
A 20 ohm resistor and 50µF capacitor are connected in series with an A.C source having amplitude of 10 V and frequency 125 Hz. Calculate:
A 50Hz, single phase transformer has a ratio of N2:N1 = 0.2. On full-load, the secondary current is 200A. The resistance and reactance of the primary winding are 0.8 ohm and 4 ohm respectively. The corresponding values for the secondary winding are 0.04 ohm and 0.1 ohm. If the secondary is short circuited, what voltage must be applied to the primary to produce full-load current? What will be the copper loss?
The PLC-5, SLC 500, and MicroLogix use a(n) ____________________ instruction for moving data from one word to another.
Consider the diode circuit shown below. If in the given circuit, Vs is replaced by a 12V battery and diodes D1 & D2 are considered ideal, what is the potential Vout equal to?
Could you solve this with clear steps ?!
A resistance 120 Q and a capacitance 15 µF are connected in series across a 240 V, 50 Hz a.c. supply. Calculate (a) the circuit impedance (b) the voltage across the resistance (c) the voltage across the capacitor and (d) phase angle in degrees.
Which of the following is true about all series ac circuits?(a) The voltage across any circuit element is a maximumwhen the current is a maximum in that circuit element.(b) The current at any point in the circuit is always thesame as the current at any other point in the circuit.(c) The current in the circuit is a maximum when thesource ac voltage is a maximum.(d) Resistors, capacitors, and inductors can all change thephase of the current.