Question 4 The line-to-line voltage of an overhead distribution line is 100 kV and radius of the line conductor is 2 cm. If the geometric factor of the configuration is 18, determine; (a) uniformity factor and (b) field stress on the conductor surface to check whether it exceeds the strength limit of the air. E (r) : 2r In- Field intensity variation between lines is expressed as 2r d

Question 4 The line-to-line voltage of an overhead distribution line is 100 kV and radius of the line conductor is 2 cm. If the geometric factor of the configuration is 18, determine; (a) uniformity factor and (b) field stress on the conductor surface to check whether it exceeds the strength limit of the air. E (r) : 2r In- Field intensity variation between lines is expressed as 2r d

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Companies designs, creates, and sells Integrated Circuits (chips). What do your buyers useto compare your IC products against your competition’s? Give 3 types of IC benchmarkmeasurements in short answer
Q2/ Fill in the blanks with appropriate conjunction ( but, although, however, so, because) 1. L like him I don't want to spend every evening with him. 2. She liked him . she did not want to marry him. 3. . .John had more years of experience than Peter, he did not get the promotion. 4. She wanted to go on holiday . she was short of money. 5. few people participated in the program, it was a commercial success. 6. I find it relaxing, I often go to movies.
Logic
I need the answer as soon as possible
21)This multiple choice question from MEASUREMENTS INSTRUMENTATIONS course.
I need the answer as soon as possible
TOPIC: Power Systems, Power Plants & IlluminationINSTRUCTIONS:- Answer in this format: Given, Illustration, Required Conversion, Solution, Final Answer.- Step-by-step solution, do not skip even simple calculations to avoid confusion.- If answered in written form, make sure it is readable.PROBLEM:A substation supplies power by four feeders to its consumers. Feeder No. 1 supplies six consumers whose individual daily maximum demands are 70 kW, 90 kW, 20 kW, 50 kW, 10 kW, and 20 kW, while the maximum demand on the feeder is 200 kW. Feeder No. 2 supplies four consumers, whose daily max. demands are 60 kW, 40 kW, 70 kW, and 30 KW, while the maximum demand on feeder No. 2 is 160 kW. Feeders Nos. 3 and 4 have a daily maximum demand of 150 kW and 200 kW respectively, while the maximum demand on the station is 600 kW. Determine the diversity factor for the four feeders. 1.18 1.25 1.30 1.36
4. In your own words what is safety?
Refer to the National Electrical Code® or the working drawings when necessary. Where applicable, responses should be written in complete sentences. For problems 1 and 2, six luminaires, similar to Style E used in the Commercial Building, are to be installed in a room that is 12 ft x 18 ft (~3.7 m x ~5.5 m) with a 9 ft (2.8 m) floor-to-ceiling height. The spacing ratio for the luminaire is 1:0. 1. The maximum distance that the luminaires can be separated and achieve uniform illuminance is ft ( m). For problems 2-5, two luminaires, 8 ft (2.5 m) and 4 ft (1.2 m) in length with dimensions as shown in Figure 15-7, are to be installed in tandem (end to end). The end of the long luminaire is to be 2 ft (600 mm) from the wall. 2. The center of the outlet box should be roughed in at ft ( m) from the wall. 3. The first support should be installed at the wall. ft ( m) from 4. The second support should be installed at from the wall. ft ( m) 5. The final support should be installed at the wall. ft…
None
The illustration below shows the components of a simple circuit diagram.choose from the choices on the left the best term or description that will match each component and the function.write your answer on the prescribed box
Could you please solve the remaining question :)