QUESTION 3 The value of stress concentration factor depends on the geometry. If K₂ and Ky are stress concentration factor for case (a) and case (b), respectively, which answer of the following is true? окажко KA = KB KA < KB O None of the rest. P

Q: 50 MPа 80 MPа 80 MPа 50 MPа

A:

Q: . For the plane stress situation shown in the figure, the maximum shear stress and the plane on…

A: A plane stress system as shown-Stress values-,To Find-The value of the maximum shear stress and the…

Q: The thin bar is subjected to an increase in temperature along its axis. Determine the end B of the…

A:

Q: Question 4 The state of stress is showing as a particular point in a stressed body. The diameter of…

A: Given- State of stress is given- σx=100 MPaσy=-50 MPaτxy=50 MPa It is needed to find the diameter…

Q: As shown in the figure, the simply supported beam is only subject to the action of dead weight, the…

A:

Q: Learning Goal: To determine the in-plane principal stresses and maximum shear stress along with…

A: If you have any doubts please comment

Q: The state of stress at a point in a body is = 100 MPa. If given by σx = 50 MPa and oy o one of the…

A:

Q: the x-y element. The sketch must include the magnitude of the angle between the x and n axes and an…

A:

Q: Mohr's circle is shown for a point in a physical object that is subjected to plane stress. Each grid…

A: Size of grid square, Number of grid from origin to x about horizontal axis, Number of grid from…

Q: 1- Consider the unit cube shown in the Figure, which undergoes the deformation: x₁ = a (x₁ - - X₂),…

A:

Q: 2D stress at a point is given by a matrix - [13 = 30 20 shear stress in MPa is P Oxx Txy Тух буу Oyy…

A:

Q: Principal Stress or Strain Question If the principal stresses in a plane stress problem, are 0₁ =…

A: Principal stresses in a plane stress σ1=100 MPa,σ2=40 MPa.

Q: An element in biaxial stress is subjected to stresses o, = -60 MPa and oy = 18 MPa, as shown in the…

A:

Q: Problem 4- For the following cross section (all dimensions in mm) determine: a) The location and…

A: Calculating the location of neutral axis,

Q: Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses…

A: Given data : Normal stress in X direction :σX=-107 MPaNormal stress in Y direction :σY=172 MPaShear…

Q: 1. Given stress on an element as shown. a) Using both Analytical method and Graphical method…

A: a) Analytical Method i) σ1 , σ3 σx = - 75 MPa σy = 40 MPa τxy = 20 MPa σ1,3=σx + σy2 ± (σx - σy2)2 +…

Q: Given the following illustration: A e B W e A weight, W, is held in place by a steel rod at AB and…

A: Stress in rod AB=450MPaStress in rod BC = 300MPaDiameter of rod AB=16mmDiameter of rod BC=25mm

Q: Question 2 [29] Evaluate the stiffness matrix for the element shown in Figure 2. Assume plane stress…

A: Stiffness: The load required to produce the unit deformation (or) moment required to produce a unit…

Q: What is meant by strain transformation? Describe two procedures for obtaining stress form Mohr’s…

A: Strain transformation equations are given as : This is similar to stress transformation equations,…

Q: omponents &n, Et, and Ynt at the point if the n-t axes are rotated with respect to the x-y axes by…

A: Strain is ratio of change in length/original length. In this question normal &amp; shear strain is…

Q: For the shear strength versus normal stress graph in Figure 1 and the shear strength relationship,…

A:

Q: The state of stress of an element is given as follows. The value of normal stress are = 30MPa, σ₂ =…

A: Given data, The value of normal stress in x and y axis, σx=30 MPaσy=-10 MPa. Major principal stress,…

Q: For the stress element below, when a = 9, b = 4, MPa. Calculate your answer to stress, is: Input…

A:

Q: 3. The picture shows a triangular element, area AB is free surface, angle B=30°, request Stress…

A: Given : Required : Normal Stress component along x direction and shear stress in X-Y plane

Q: the stress components at point H. And show the stress state for this point on a volume cubic element…

A: Given data Axial Load for Point H is P=3 kN Shear Load for Point H in Y direction is VY=0.5 kN Shear…

Q: The biaxial stress system in an element is shown in the figure. Which of the following will give the…

A: Given- biaxial stress system-σ1=60 N/mm2σ2=-40 N/mm2θ=45o

Q: 4. Consider a unit cube of a solid occupying the region 0 ≤ x ≤ 1,0 ≤ y ≤ 1,0 ≤z ≤ 1, After loads…

A:

Q: Rev Part C-Orientation of the element subjected to maximum shear stress on its sides Determine the…

A:

Q: 1- Consider the unit cube shown in the Figure, which undergoes the deformation: x₁ = α (X₁ X₂), x₂…

A:

Q: In order to determine the shear stress at A, using the shear stress formula, the thickness would be…

A:

Q: 90 MPa 55 MPa 70 MPa 55 MPa 90 MPa 65° TE 70 MPa The state of stress on an element relative to the…

A: Given :   Required : Original state of stress and angle of rotation  Stress at rotated element…

Q: The strain components Ex, Ey, and Vxy are given for a point in a body subjected to plane strain.…

A:

Q: Principle stresses of 100 kPa (tension) act on two mutually perpendicular faces of a rectangular two…

A: Principle stress=100 kPa

Q: Determine the stress components at point H. And show the stress state for this point on a volume…

A: Given Data: Axial Load for Point H is P=3 kN. Shear Load for Point H in Y direction is VY=0.5 kN.…

Methods to Determine Vertical Stress

The load applied to the soil is transferred to the underground. The presence of water at soil pores and solid grains above the soil are the primary components that are responsible for the effective load transfer. Due to the load acting, the internal component of the soil or the underground formations undergoes deformations or a tectonic shift. The amount of deformation depends upon the amount of load acting on the soil surface, which indeed, depends on the weight of everything present above the soil. Due to this, the underground soil element develops internal stresses which try to resist the tectonic changes.