Question 3 The results of an open loop frequency response test are presented in Table Q3. o (rad/s) 0.1 Gain (dB) 40.0 26.0 20.0 14.0 Phase (°) -90 0.5 1 2 4 7 10 20 50 100 5.0 -3.0 -9.0 -24.0 -46.5 -65.5 -99 -107 -124 -149 -174 -192 -221 -250 -260 Table Q3 a) Plot the bode diagram for the system b) Evaluate the following terms : i) gain crossover frequency ii) phase crossover frequency ii) gain margin iv) phase margin

Question 3 The results of an open loop frequency response test are presented in Table Q3. o (rad/s) 0.1 Gain (dB) 40.0 26.0 20.0 14.0 Phase (°) -90 0.5 1 2 4 7 10 20 50 100 5.0 -3.0 -9.0 -24.0 -46.5 -65.5 -99 -107 -124 -149 -174 -192 -221 -250 -260 Table Q3 a) Plot the bode diagram for the system b) Evaluate the following terms : i) gain crossover frequency ii) phase crossover frequency ii) gain margin iv) phase margin

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The midrange voltage gain of a certain RC coupled amplifier is 150 and the dominant critical frequency of the amplifier at the low frequency region is IkHz and the critical high frequency is 1MHz. Determine the voltage gain (in dB) at the following frequencies: 100 Hz, 200 Hz, 1 kHz, 10 kHz, and 1 MHz
3rd Class Electronic Circuit Homework (1): Frequency Response Q) Draw and find the equivalent cct, low and high frequency responses, and overall gain (Av)? Hint: Use any value you want for the Rs and RL. Vcc BDc = Bac = 125 Che = 25 pF Che = 10 pF +9 V %3D Rc 220 N C3 V out R1 12 k2 1 µF RL 1 µF Ω Rs R2 4.7 kN RE 100 Ω C2 10 µF Vin
[Q3B] Draw a Bandpass filter which generate the response in the figure below A (mid) -40 dB/decade -40 dB/decade for for
= b) A three-stage amplifier system operated at T 25°C and 1 MHz bandwidth which is determined by an LC-tuned circuit. The first stage has a power gain of 10dB and an NF of 5dB, the second has a power gain of 20dB and NF=10dB, and the third stage has a power gain of 30dB and NF=10dB. The output load is 2000. The input noise is generated by a 20k resistor. Calculate: i) The noise voltage and power at the input and the output of this system assuming ideal noiseless amplifiers. ii) The overall noise figure for the system. iii) The actual output noise voltage and power.
(b) Block diagram of a system with unity feedback is illustrated as R(s) Y(s) K G(s) Figure Q3(b) and the transfer function is given as 50000 G(s) = s² + 150s + 5000 From the given block diagram and transfer function, sketch an approximate magnitude and phase of Bode Plot. Choose any value of K that you might think will simplify your sketching. There is no requirement of K value in this sketching process. The selection of Kis only necessary if you have a particular design requirement.
Analog Electronic: Frequency Response of BJT and FET Amplifier
Q3: Find the lead , lag and lead lag component values and implement the complete setup for the compensators shown below 2. 3. V.(3) Transfer function, V6) Function Network Lag compensation R: stRr R + R2 s+R + R2)C Lead compensation RC RC +1 Lag-lead compensation R2
Determine the output voltage waveform in Figure 2-58 if both dc sources are 10 V and the input voltage has a peak value of 20 V.
In the circuit in the figure Vcc= 25 V, Vi= 40 mV, RB = 470 kg. RC = 3.3 kg, RE1 = 470 G, RE2 = 1.2 kg RL = 32.5 k(2 and B = 110 because you find the value of the output voltage (Vo) according to. Note-1: capacitors are worth neglecting at mid-band frequency. Note-2: the output impedance (ro) of the transistor will be ignored. RB Q1 NPN RC
This circuit represents a small signal amplifier.If C1= 1.5 μF, C2= 0.43 µF Assuming the transistor has: ac current gain =100. dynamic resistance = 100, and Internal Capacitances C= 42 pF, Chc-4pF, C=1pF. 1- Calculate the critical frequencies for the low frequency response. 2- Calculate the critical frequencies for the high frequency response. 3- Write the general formula for voltage gain as function of frequency. 4- Sketch the Bode Plot for the voltage gain magnitude. 2 T mill 1kQ2 O 560 ΚΩ 4.3 ΚΩ C2 HA R1 2 2,7 ΚΩ
3. a) b) Write a short note on Nyquist Rate. Calculate the Nyquist rate in rad/sec and in Hz for, m(t) = 2 sinАnt · cosВnt
i need the answer quickly