Question 3 Solve for K and a that yields a Ky = 1000 and 20% overshoot for the unity feedback system below: G(s) = K s(s+ a) K = 831,744 and a = 831.744 K = 318,744 and a = 318.744 K = 813,744 and a = 813.744 O K = 381,744 and a = 381.744

Question 3 Solve for K and a that yields a Ky = 1000 and 20% overshoot for the unity feedback system below: G(s) = K s(s+ a) K = 831,744 and a = 831.744 K = 318,744 and a = 318.744 K = 813,744 and a = 813.744 O K = 381,744 and a = 381.744

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q4: Design a buck-boost converter to provide an output voltage 12V from a source that varies 'between 10V-16V. Given the load resistor is 10 ohm. assuming the frequency is 50 KHz and the output voltage ripple is 1.5% Specity: a. The duty ratio. b. The value of inductor. c. The value of capacitor. Note: Determine the values of inductor and capacitor with D1 only.
What are the pros and cons of open loop system and close loop system? cons the control
Question 2Describe the following feedback control system in terms of simple block diagrams:a. DC motor position control systemb. Antenna Control systemFor each system, indicate the location of the following elements and mention the unitsassociated with each parameters The process The desired output signal Sensor Actuator Controller Controller output Reference Error
Control Systems
Pls do correct and handwritten
Automatic Control
Control systems solve all parts or i will dislike
A) Sketch the P&ID for the system after adding the feedforward and feedback controllers. B) Draw a block diagram for the system in (A) C) Design the feedforward controller. D) No calculations are required: is the feedback control loop stable? E) What is the purpose of having the feedback control, in addition to the feedforward control? Ti, F Feed T, F Product heating stream Figure 3
Answer the following questions using the figure below of the basic regulating controlling system: 1. What is the type of control system? II. Explain how the system takes input voltages to control the system. III. Write about the amplification unit (what is the type of the op-amp? And how it drives the output?) and the transducer unit (why it is needed? And how it works?) Feedback Amplifier Motor Load Input voltage transducer Edit View Insert Format Tools Table
QUESTION 16 Consider a unity negative feedback control system. It is assumed that the plant G(s) includes an integrator and you are using a proportional compensator K. You want to increase the closed-loop ramp tracking performance. Currently, the steady-state tracking error of the closed-loop system with KK_old to a unit ramp signal is 0.1. You would like this error to be reduced to 0.025 with a new proportional compensator K=K_new. How does the proportional gain have to change to make this possible? We assume that the closed-loop is stable for all values of the proportional gain. K_new = 4.33 K_old K_new = 4 K_old K_new = 0.25 K_old OK_new = 5.44 K_old QUESTION 17 Given that G(s) = 2.1(s+10)(s-5)(s(s+6)(s+7)), calculate the phase of G(w) in radians for a frequency of 7 rad/s. Provide your answer with two decimal precision.
Feedback and control system Give a good examples of control system mechanized/component in your everyday life.
I need a comparison between an Open Loop, Feedforward and Feedback control systems. If you can also use a table with numerical values to compare them in addition to theoretical would be appreciated. Thanks in advance!