QUESTION 3: Figure 13.10 shows AC equivalent circuit for 741 Input Stage. Given that ß = 200, V₁ = 50 V, IC1 = 8.8 µA, R₂ = 2 kQ, and R₁₂ = 3.235 MQ findAdvo1/vd=-8m2 (ro4 || Ract1 || R₁2 ).Format: 0.234259674658438m2 (mA/V)ro4 (ΜΩ)Format : 8.3577588964875Format: 7.5534575377999Ractl (MQ)Ad (V/V)Format: -854.65958746777viel23R₁TTOA24\iaR₂iel26RactlovolR₁₂2

Answered: Image /qna-images/answer/66c6697b-89a3-4e5b-a25c-f4348f5152f1.jpg

QUESTION 3: Figure 13.10 shows AC equivalent circuit for 741 Input Stage. Given that = 200, V=50 V, IC1 = 8.8 μA, R₂ =2 k2, and R2 = 3.235 MN fin Advo1 /va=-8m2 (ro4 || Ract1 || R₁2 ). 8m2 (mA/V) ro4 (ΜΩ) Ractl (Mn) Ad (V/V) 21 23 25 Tot 2₂ 24 id 26 Format: 0.23425967465843 Format : 8.3577588964875 Format: 7.5534575377999 Format: -854.65958746777 Raci R₁₂2 Vol

QUESTION 3: Figure 13.10 shows AC equivalent circuit for 741 Input Stage. Given that = 200, V=50 V, IC1 = 8.8 μA, R₂ =2 k2, and R2 = 3.235 MN fin Advo1 /va=-8m2 (ro4 || Ract1 || R₁2 ). 8m2 (mA/V) ro4 (ΜΩ) Ractl (Mn) Ad (V/V) 21 23 25 Tot 2₂ 24 id 26 Format: 0.23425967465843 Format : 8.3577588964875 Format: 7.5534575377999 Format: -854.65958746777 Raci R₁₂2 Vol

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q2) Design a Bridge FWR to supply a load of (1002) with the waveform shown in figure from the main power supply of (220 Vrms). Find: - 1- The transformer turns ratio (a). 2- The ripple voltage. Vot Vm = 12 V 3- The Vde value. 4- The RMS value of the output voltage. 5- The ripple factor. 6- The value of capacitor filter. Vip = 0.1 V (assume ideal diodes) T=0.01 sec. tisec) Q3) V in Design a regulated circuit to supply a constant voltage of (10 V) across a resistive load of (50 2). The input voltage is shown in the figure. The minimum current for the Zener diode operation is (Izk=5mA). Find the 15 V 15 maximum power dissipated in the Zener diode. 12.5 12 V 10
i need the answer quickly
Paga No. Date play computars, lectronic and vothar An RLC cireuit cau be The electric circuit important role in lange can notwarks in branches usedas y engineering. Dand- pass Jilter, high pass filltan . The Ric lilteris described as a socond arder circuit, band-stop fillken, low -pars filtor. or that meaning any voltage er curront in qthe sorand order Sdescribe by diffprenial coquation in cirauit analysis .Onesuch LCŔ series cincuit is considered here with R=2 circuit can be a L=l Henri, C=LF and E=4.4 sin Clot)valta. a State damped, whether the circuit zopresents the ovee ne underdamped or enitically dampad. cases ? Assuming the initial current cand the change is zeng Sind the charge 2 current in the eircuit aut au instaut y time t. O Write the steady change on the plati of capacitor. A Weite ghe dransient slution for the charge,
Op amp and diodes are ideal. Derive Vout and sketch the transfer curve of Vin vs Vout. Please show complete solution.
Parts D and E only please, thank you!
What can you say about AM DSB-FC, AM DSB-SC, and AM SSB? What do they have in common and their difference?
Give an example of an analogue device that can be used as a phase comparator in a PLL system and explain its operation.
Prob 1: For each of the 8 circuits below, draw small signal model and calculate Vout/Vin. Vb1, Vb2 are dc voltage sources. and I1 is an ideal dc current source. Ignore body effect for all problems. Vino M3 M₂ M₁ (a) VDD J Vb₁ M3 (e) VDD VinM₂ Vb2M₁ Vb3 Vb2 - Vout Vb1 Vout HE Vout o Vb₁ VinM₂ 46! M3 (b) VDD B M₁ T. M3H (f) VDD VinM₁ M₂ Vout VinM₂ 4M₁ (c) M3 M3 VDD VDD 74 Vb1M₂ Vino M₁ (g) Vout Vout Vb1 Vb2 HE Vin VinM₂ M3 M3 VDD (d) HL M₁ M₁ -o Vout M2o Vout 1₁ (h) VDD
(Boost de-dc converter with continuous inductor current. Evaluation of inductor and capacitor values) EX3: The boost converter shown bellow has the following specifications: Vin = de input voltage = 12 V, de output voltage = 30 V, output voltage peak-to-peak ripple = 1% Inductor current peak-to-peak ripple 10%, f;= switching frequency = 25 kHz and R = load resistance = 50 N Assuming that the converter is ideal, calculate: a) The duty cycle. b) The average input current. c) The minimum required inductance that ensures continuous inductor current. d) The required inductance so that peak-to-peak current ripple = 10%. e) The minimum and maximum values of the input current. f) The value of the output capacitor so that the output voltage ripple = 1%. g) Verify the theoretical results with the respective simulation ones. Boost inductor Output filter capacitor D VL 1R Vin S R Vo