Question 3 Determine the factored compression resistance of a 6m long column manufactured from a 203x203x46 H section (Grade S355JR). The column is pinned at the bottom and fixed at the top. Lateral restraint is provided to the Y-axis at mid-height. The structure is braced to prevent sway. 3000 6000 3000 H X-AXIS Y-AXIS

Question 3 Determine the factored compression resistance of a 6m long column manufactured from a 203x203x46 H section (Grade S355JR). The column is pinned at the bottom and fixed at the top. Lateral restraint is provided to the Y-axis at mid-height. The structure is braced to prevent sway. 3000 6000 3000 H X-AXIS Y-AXIS

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter10: Plate Girders

Section: Chapter Questions

Problem 10.7.8P

See similar textbooks

Similar questions

In the built-up girder shown below that has an unbraced length of 25 ft. (L-25 ft) and moment gradient factor of C,-1, determine the maximum flexural design strength. E-29000 ksi Fy-50 ksi PL 25x0.6" PL 35*0.3" PL 25x0.6"
A column section b- 400 mem, h - 600 mm is reinforced with longitudinal bars Ast - 12-020 mm equally distributed along all faces. Lateral ties are composed of 12 me rectangular hoops with clear cover equal to 40 mm and 12 mm cross ties in both directions. Concrete yield strength f'c - 27 MPa and steel yield strength, fy - 415 MPa. Calculate the nominal axial strength of the column in kN. O 6,985 O 5,588 O 5,938 O 5,239
1. Check the beam shown for compliance with the AISCS. Lateral support is provided only at the ends, and A992 steel (E345 MPa and Fu= 450 MPa). The only uniform service dead load is the weight of the beam. The 70 KN service loads are 30%DL and 70%LL. Use LRFD. IR₁ 0.90m 70,KN * W14 x 68 1.20m 70 KN * 0.90m R₂ W14x68 70 KN
1. Check the beam shown for compliance with the AISCS. Lateral support is provided only at the ends, and A992 steel (E 345 MPa and Fy= 450 MPa). The only uniform service dead load is the weight of the beam. The 70 KN service loads are 30%DL and 70%LL. Use LRFD. 70 KN 70, KN 70 KN W 14 x 68 0.90m 1.20m 0.90m WI4 x68 IR, R2
5. The beam-column has a height of 7.5m and is a member of a braced frame. It is subjected to an axial load of DL-65KN and LL= 1OOKN. It is pinned at both ends. A W12X35 section was used and was made up of A-36 steel with Fy-250MPA. Compute the interaction value for beam- column based on NSCP 2015 code provisions. Ngelect the weight of the section. A = 6645 mm2 Zx- 839x10^3 mm3 d- 317.50mm Sx- 747x10^3 mm3 tw= 7.62 Rx= 133.35 bf= 166.62 ly= 10x10^6 mm4 tf- 13.21 Sy= 122x10^3 mm3 Ix= 119x10^6 mm4 Ry3 39.12mm 3.5 Note: Use C=D1.00%--0.2
USE NSCP 2010 A rectangular beam reinforced for both tension and compression barshas an area of 1450 mm² for compression bars and 4350 mm² fortension bars. The tension bars and compression bars are placed at a distance of 600 mm and 62.5 mm respectively from the top of thebeam. The beam width 300 mm, fc’ = 21 MPa, fy = 415 MPa andtension steel covering is 60 mm.If it is 8 m-simply-supported beam that carries three concentratedservice live loads P applied at three quarter points of the beam (exceptat the supports), neglecting the self weight of the beam, determine themaximum value of service load P in kiloNewtons.
A concrete circular column with a radius of 350mm has f'c-25 MPa and is braced against sidesway. The column is assumed to be pinned on both ends with an unsupported length is 6.1meters. The column is subjected to the following service loads: Axial Dead Load =350 kN Axial Live Load=480 kN Moment due to Dead Load on the top of the column = 125 kN-m Moment due to Dead Load on the bottom of the column = 60 kN-m Moment due to Live Load on the top of the column = 122 kN-m Moment due to Live Load on the bottom of the column = 75 kN-m. If the moments bent the column in a singular curve, determine the following: 1. Critical Load on the column, kN 2. Moment Magnifying factor 3. Design Moment of the column, kN-m.
Bearing plate is design to distribute the reaction of W12x65 with a span length of 12 ft center-to-center of supports. The total service load including the beam weight is 15 kips/ft with Live load / Dead load ratio equals to 2. The beam is to be supported on RC walls with f’c =4,000 psi. For the beam, Fy = 50 ksi and Fy = 36 ksi for the plate. Use LRFD. If ℓb = 8 inch and B = 14 inch, what is the minimum computed thickness of the bearing plate in inch? Express your answer in three decimal places.
Bearing plate is design to distribute the reaction of W12x65 with a span length of 12 ft center-to-center of supports. The total service load including the beam weight is 15 kips/ft with Live load / Dead load ratio equals to 2. The beam is to be supported on RC walls with f'c =4,000 psi. For the beam, Fy = 50 ksi and Fy = 36 ksi for the plate. Use LRFD. What is the minimum bearing length, {, to prevent web yielding in inch? Express your answer in two decimal places.
The frame shown below is subjected to uniformly distributed load of 2.6KP.. Determine the maximum moment of member BF (assume simple beam support) A E, 1.5m F 1.5m 351 C 1.5m H 3m B
A bracket of length 1.5m is rigidly attached to the simply-supported beam at its end. The beam is subjected to the combined effect of M,, M, and compressive force P caused by the factored loads as shown. There are lateral supports only at the ends. The member is made of HE300A section and steel grade is S275 (Fy-275MPA, Fu= 430 MPa). The loads acting are determined from LRFD combinations. Determine whether the member can safely carry the applied loads. Multiply first-order moment diagrams by a factor of 1.2 to account for second-order effects. No need to check shear limit state. You do not need to additionally consider the beam self-weight. E Use the following simple expression to calculate the value of L:: L, = T*rts 0.7*Fy y P = 400kN 1.5 m F = 150kN 2 т 4 т X: Lateral support НЕЗ00А
A built-up section consists of S150x26 and two channels C380x74 having an effective length of 6m. The section is pin connected at both ends. Use A572 Grade 50 Steel (Fy = 345.58MPA) and NSCP2010 Specifications. a. Compute the slenderness ratio of the column section. b. Compute the allowable compressive axial stress. c. Compute the capacity of the column section. Properties of One C380x74 A = 9,480mm2 Ix = 168 x 106 mm4 ly = 4.6 x 106 mmª x = 20.3mm d = 381mm 20.3 -73.9 20.3 -73.9- rx = 133mm Ty = 22mm tw = 18.2mm (s isox26 Properties of One S150x26 A = 3,250mm2 Ix = 10.8 x 106 mm4 ly = 0.952 x 106 mm4 d = 152mm rx = 57.7mm ry = 17.1mm C 380x74 -152- 18.2 18.2