: The two (4x4x3/8) angles shown below are connected by 4 in E70XX fillet welds to a 5/8-in thick gusset plate as indicated. The angles and gusset plate are fabricated from A36 steel. Determine the tensile force that may be applied to the connection. The applied load is concentric with the weld group.

: The two (4x4x3/8) angles shown below are connected by 4 in E70XX fillet welds to a 5/8-in thick gusset plate as indicated. The angles and gusset plate are fabricated from A36 steel. Determine the tensile force that may be applied to the connection. The applied load is concentric with the weld group.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Topic:Bolted Steel Connection - Civil Engineering *Use latest NSCP/NSCP 2015 formula to solve this problem The butt connection shows 8-22 mm dia. A325 bolts spaced as follows: S1 = 40 mm S3 = 50 mm t1 = 16 mm S2 = 80 mm S4 = 100 mm t2 = 12 mm Steel strength and stresses are: Fy = 248 MPa Fu = 400 MPa Allowable tensile stress on the gross area = 148 MPa Allowable tensile stress on the net area = 200 MPa Allowable shear stress on the net area = 120 MPa Allowable bolt shear stress, Fv = 120 MPa Bolt Hole diameter = 25 mm Questions: Calculate the allowable tensile load T, under the following conditions. a) Based on the gross area of the plate b) Based on the net area of the plate c) Based on block shear strength
Please Use LRFD * ASD!
Considering the following steel connection. The plates in Pink are 9mm steel plates. The middle plate (Yellow) is 18mm thick. The width of the plate is 100mm. The maximum allowable tension stresses on any of the plates is 100Mpa in Gross Area Yielding and 150 Mpa for Net Area or Tension Rupture. The bolts used are 8mm in diameter, the holes are 10mm in diameter, no need to add 1.6mm. The bolts allow a maximum of 280 Mpa of shear. Determine the maximum allowable "P" of the connection in kN.
Regardless of the design load, the effective length of a 5/8 in. fillet weld that is subjected to stress in a longitudinal direction should not not be less than A. 2 in. B. 2 1/2 in. C. 3 in. D. 3 1/2 in.
Please correct answer otherwise dislike
Topic:Welded Connection - Civil Engineering -Steel Design *Use latest NSCP/NSCP 2015 formula to solve this problem *Please use hand written to solve this problem A plate is attached to the frame of a machine by side fillet welds as shown in the figure. Determine the size of the welds to resist a vertical load of 150 kN. Assume that the allowable shearing stress at the throats of the weld is 145 MPa.
The tension member is a PL 1⁄2 × 6. It is connected to a 3⁄8-inch-thick gusset plate with 7⁄8-inch-diameter bolts. Both components are of A242 steel. Note: A242 Fu = 70ksi dh = db + 1/16’’ Use: Consider deformation at the bolt hole what is the: minimum spacing as per AISC code provisions maximum spacing as per AISC code provisions minimum edge distance as per AISC code provisions maximum edge distance as per AISC code provisions
Five M20 8.8/ bolts are used in the connection between a beam and a column. Both sides of the cleat plate are welded to column using fillet weld (Manual metal arc AS4855 B-E43XX) with size of 5 mm. The design force transferred from beam to column is 300 kN. The cleat plate has thickness of 12 mm, fy = 300 MPa, and fü = 360 MPa. Determine the unit stress sustained by the weld
A tension member splice is made with 14-inch E70 fillet welds as shown in Figure 5. Each side of the splice is welded as shown. All steel is A36. Determine the maximum service load, P, that can be applied if the live load to dead load ratio is 1.5. Note: Assume that the base metal shear strength is adequate (check the yielding strength for the gross area, fracture strength for the effective net area, weld strength and block shear strength). PL 5/8x8 4 in. Figure 5 2 PL 7/16x4