Question 3 (a) A pipe of 300 mm diameter conveying 0.30 m/s of water has a right-angled bend in a horizontal plane (90°) as shown in Figure Q3(a). Find the resultant force exerted on the bend if the pressure at inlet and outlet of the bend are 24.53 N/cm2 and 23.54 N/cm2. Assume the density of water is 1000 kg/m³.

Question 3 (a) A pipe of 300 mm diameter conveying 0.30 m/s of water has a right-angled bend in a horizontal plane (90°) as shown in Figure Q3(a). Find the resultant force exerted on the bend if the pressure at inlet and outlet of the bend are 24.53 N/cm2 and 23.54 N/cm2. Assume the density of water is 1000 kg/m³.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Use density of water = 1000kg/m^3 and acceleration due to gravity equal to 9.81m/s^2. A rectangular tank containing water at a depth of 1.2m is accelerating towards the right, the motion of which is parallel to the longest side. If the tank has the following dimensions: length = 3 meters, width = 1.8 meters, and height = 1.5 meters, determine the following: the maximum allowable acceleration (m/s^2) of the tank; and the unbalanced force causing the maximum acceleration in kN. angle (in degrees) of fluid inclination of the acceleration from part a. how many cu.m of water is spilled when a = 2.5m/s^2. Note: Do not include units in your answers. Do not round off intermediate values and answer in four decimal places.
4.129 For the system shown in Fig. P4.129, estimate the downstream pressure p2 if p1 V1 = 20 m/s. Neglect losses. (Note: The pressure immediately after the pipe expansion is p1.) 30 kPa and | P2 P1 6 cm dia. Water V1 V2 3 cm dia. Fig. P4.129
Q2) Several water pipes intersect at the junction box illustrated in Figure. Determine the force required to keep the junction box in place. Assume water at 4°C. 250 mm Q₁ = 0.2 m³/s P₁ = 480 kPa 350 mm 300 mm QIVA = 0.3 m³/s /P = 400 kPa 30° Q=0.1 m³/s Pc = 450 kPa 50⁰ 200 mm 60° Q = 0.4 m³/s PD = 350 kPa
4.131 Water flows steadily through the double elt shown in Figure P4.131. Water flows into the elbow from the top at 5 m/s, and from the left at 15 m/s. Determine the vertical and horizontal components of the force needed to hold the elbow in place. wowV2= 5 m/s ba N 450 mm P2 = 30 kPa %3D P1 = 250 kPa 250 mm V = 15 m/s 200 mm P3 = 170 kPa V3 40° Figure P4.131
Pls do stepl by step solution. Show me how to convert l/s to m/s and all steps. Thank u very much
4.5 The water flows in a 4m wide canal at a velocity of 5 m/s. A wedge-shaped column bifurcates the stream, as shown in Fig. 4.29. Calculate the force per unit depth exerted by the water stream on the column, if the wedge angle (a) is 30°. V=5m/s V=5 m/s V=5 m/s Fig. 4.29 [Ans: 3407.4N]
A 5-gal, cylindrical open container with a bottom area of 120 in^2 is filled with water and rests on the floor of an elevator. If cylindrical container is accelerated upward at 3 ft/s^2, what resultant force does the container exert on the floor of the elevator during this acceleration? The weight of the container is negligible. (Note: 1 gal = 231 in^3)
Water is transported from reservoir A to reservoir B by a pump. The diameter of pipe D1 is greater that the diameter of pipe D2 (D1>D2). The reservoir B is elevated from the ground at Z units. Draw the hydraulic gradient line and energy gradient line for the system. D2 A D1 Pump
The horizontal nozzle shown in figure has D₁ = 12 in. and D₂ = 6 in. with inlet pressure p = 38 lbf/in2 absolute and V₂ = 56 ft/s. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. DO Bolt force = Water Pa= 15 lbf/in² abs Assuming that p₁ is unknown and using Bernoulli's equation with no losses, compute the new bolt force for this assumption. lbf Open jet
Find potential energy m=2.203 kg g=10 m/s2 h=2.2 m
The counterweight pivot gate shown in Fig. 2.85 controls the flow from a tank. The gate is rectangular and is 3 m x 2 m. Determine the value of the counterweight W such that the upstream water can be 1.5 m deep. Fig. 2.85 Problem 2.27
Q3: Water flows from reservoir A through pipe 1, diameter d, = 120 mm, length L=100 m, to, junction D from which the two pipes leave, pipe 2 diameter dz=75mm, length L2=50 m goes to reservoir B, and pipe 3, diameter d;-60 mm, length L;-30 m goes to reservoir C. Reservoir B is 12 m below reservoir A, and reservoir C is 20 m below reservoir A. All pipes have f 0.01. Calculate the head at junction D required to achieve direct flow from this junction to reservoir B.