Question 3Sclo-"* The diagram illustrates a pressure measuring system.yo12mvmAmeteriii.converterpressure inputThe system consists of pressure transducer connected to a converter. The output mV isTelated to the input pressure by V = 30p where p. is in bar and V is in mV. The converteroutput in mA is related to the input by I = 4 + 0.2V. The current is sent to a meter. What isthe pressure when the meter indicates 1SMA?iv.Controb) With the aid of sketches write briefly on the followingManipi.Spring balanceBoudon gaugeii.c) A hydraulic load cell is required to measure a maximum load of 500KN. If theeffective diameter of the diaphragm is 200mm, calculate the maximum pressure to beindicated on the Bourdon gauge. Assuming the scale is linear and operates over an A.C. of 270 volts. Calculate the sensitivity of the pressure guage.fror

Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for…

Question 3 4) The diagram illustrates a pressure measuring system. mV mA meter converter pressure input The system consists of pressure transducer connected to a converter. The output mV is related to the input pressure by V = 30p where p. is in bar and V is in mV. The converter output in mA is related to the input by I= 4 + 0.2V. The current is sent to a meter. What is the pressure when the meter indicates 15mA? b) With the aid of sketches write briefly on the following Spring balance Boudon gauge c) A hydraulic load cell is required to measure a maximum load of 500KN. If the effective diameter of the diaphragm is 200mm, calculate the maximum pressure to be indicated on the Bourdon gauge. Assuming the scale is linear and operates over an A. C. of 270 volts. Calculate the sensitivity of the pressure guage. i. ii.

Question 3 4) The diagram illustrates a pressure measuring system. mV mA meter converter pressure input The system consists of pressure transducer connected to a converter. The output mV is related to the input pressure by V = 30p where p. is in bar and V is in mV. The converter output in mA is related to the input by I= 4 + 0.2V. The current is sent to a meter. What is the pressure when the meter indicates 15mA? b) With the aid of sketches write briefly on the following Spring balance Boudon gauge c) A hydraulic load cell is required to measure a maximum load of 500KN. If the effective diameter of the diaphragm is 200mm, calculate the maximum pressure to be indicated on the Bourdon gauge. Assuming the scale is linear and operates over an A. C. of 270 volts. Calculate the sensitivity of the pressure guage. i. ii.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q15 Needed to be solved this question correctly in 15 minutes In the order to get positive feedback please show me neat and clean solution for it by hand solution needed to Please provide hundred percent correct answer quickly
Calculate the output for the given circuit. R2 Vo W M ww R2 R ww R R1 Let the values are R1=625.9ohm,R2=751.16 ohm .The error voltage is =5.6 Volt and the initial value of output is 4.7 Volt. Vout = volt. Cinale slone ADC has rejection characteristics
Calculate the dc and ac components of the output signal across load RL in the circuit of Figure * Va = 150 V V, (ms) = 15 V V's V', (ms) R 500 2 Full-wave rectifier C, 15 μF C2 10µF RL 5 ka O vdc= 136.4V, Vac= 3.9V O Vdc= 163.4V, Vac= 9.3V Vdc= 13.4V, Vac= 9.9V O None of the above
The output for the following clamping circuit is shown below assuming ideal diode calculate the avarege value and r.m.s value for the output circuit Vm-10. V=5 R (1) Figure 7-2 simple parallel clippers (Ideal diodes) (7-3)
A bridge rectifier shown below will have a positive pulsating voltage as its output, To convert the output to be negative, D . O a. D1 must be reversed b. D1, D2, D3 and D4 must be reversed O c. D1, D2 and D# must be reversed O d. D1 and D@ must be reversed O e. none of these
Determine the ripple factor for the filtered rectifier circuit below when RL= 4KQ. Then explain briefly the effect of changing in the RL value on the output waveform.
Consider a PV Module with 4 solar PV cells with the Size of each 10cm x 10cm are connected in Parallel. If we connect a lamp load of 2W across this module, choose the correct statement for the above PV Module. (Assume necessary data) a. The output voltage is 0.5V, the output current is 2A b. The output voltage is 0.5V, the output current is 4A c. The output voltage is 2V, the output current is 2A d. The output voltage is 2V, the output current is 4A
You are told that the approximate diode knee voltage is 750mV, but you need to know for sure. You are told that the diode's saturation current is I, = 2.27fA. (2.27x10-15 A) and V=25mV. Determine VD. Iterate until you have the answer to 2 significant figures.
Discuss the following a. Digital to Analog and Analog to Digital Converter b. Phase Locked Loop
I need the answer quickly