Question 2 What is the probability (as a percentage) that at least one 300 year ARI (0.33% AEP) event will occur in 40 years? (no decimal point, rounded up from the 1st decimal point) Probability= %

Q: 500 Hz. The ceiling is acoustic ceiling tile (ACT), Symbol for pi = .95 at 500 Hz Using the same…

A: Room dimensions: Length  = 4 mWidth  = 7 mHeight = 3 mFloor absorption coefficient= 0.15 Wall…

Q: For the beam shown bel ow: a) Draw the shear force and bending moment diagrams; P A В D Hinge a b…

A:

Q: 9) In the section . due to . . tensile reinforcements suffer.. A) Perforated steel, high volume of…

A: In low steel section it suffers high level of stressed. And also low in the Compression.

Q: The below shows a rectangular window sumerged in oil of specific gravity 0.8. 0.76 m -0.60 m 13m…

A: As per our company guidelines we are supposed to answer only first 3 sub parts. Kindly repost other…

Q: Determine the member stresses in members AB, AC, AD, BC, and BD if the cross-sectional area for all…

A: As per guidelines we need to answer only first question so please repost rest questions separately

Q: 8. Choose from the following, the coulomb suggested a solution to this equation r= o • A. tf = C-G…

A:

Q: 6) Three behaviors what is the cross section of reinforced concrete in order and by drawing the…

A: A typical graph of force-displacement curve for reinforced concrete is shown below: In the above…

Q: For the truss and loading shown; a.) determine the force in all the truss members. 3 kN b.)mention…

A: Finding out forces in member.

Q: For the figure shown, find the velocity and acceleration of the tractor at the instant x = 15 m. At…

A:

Q: 8) In the plastic area, the use of regulations based on .. is not allowed due to.. .... ... A) ASD,…

A: Here are also warning are given initially, however I do my best as like my previous answer.    Let's…

Q: An open cylindical tank contains 18925 Liters benzene ( Sa= 0.876). The diameter of the tank is 2 m.…

A: Volume of tank (V)=18925 litre Diameter of tank(d)=2m

Q: An open cylindrical tank 0.8 m in diameter and 5 m high is full of water. It was rotated about its…

A: Given Data: The diameter of the cylindrical tank is D=0.8 m. The height of the cylindrical tank is…

Q: 5) What is the role of the cover on the rebars in reinforced concrete sections? A) Cross-sectional…

A: Covers are use to prevent from the environmental exposure of the bars.

Q: dy x³ex² dx ylny

A: Hello dear this is the solution of your problem Please see the attached solution, thanks

Q: In this method of analysis of slope deflection method, how are slope and deflection related?

A:

Q: A hydraulic structure is sized for a 50 year recurrence interval design discharge. What is the risk…

A: Given, T = 50years  Risk of exceedence in 20 years = ?

Q: Question 11 A cylindrical sediment core sample with the dimensions: diameter = 10[cm] and length =…

A:

Q: Situation 4: Terminologies ( 1. A structural element that carries a load that is applied transverse…

A:

Q: The state of strain at the point has components of € = 300 (10-). y = -260 (10-6), and Yzy = 460…

A:

Q: 10) In case of architectural restrictions, the designer must: A) Place the rebars periodically B)…

A: Warning  is being given before answering,  However I do my best.  I try to give good explanation…

Q: In a compaction test, as the compaction effort is increased, the optimum moisture content 9. A.…

A: Please refer the attached image for complete solution. THANK YOU.

Q: Following data are obtained in a shrinkage limit test: Volume of saturated soil = 10 cc Water…

A:

Q: An object fell in an open tank of oil, to a depth of 1.5 m. The pressure on the object was…

A:

Q: Which method designs a bylaw based on a coefficient?

A: Coefficient are use to minimize or maximize the value to include adequate safety in the design.

Q: a. Vv&Vs b. Vv& Vt 8. For a soil deposit having n = 33% and G = 2.6, ysaturated= 15KN/m3 , S is: c.…

A:

Q: A wire of 3 mm diameter is bent into a circle and held with its ends and just in contact. If the…

A: A copper wire with a diameter of 3 mm is bent into a circle and held with its ends just touching.The…

Q: 7) In order for a section to have elastoplastic behavior, it must: A) Tolerable anchor is greater…

A: Brief concept- Elastoplastic behavior- Elastoplastic behaviour is the combination of the elastic and…

Q: Final answers shoul be in 4 decimal places and should also have the correct Magnitude, Units, and…

A:

Q: A concrete dam is triangular in cross section and 30 m high from the horizontal base. If water…

A:

Q: 5.1 Classify the following soil using the U.S. Department of Agriculture textural classi- fication…

A: This question is from geotechnical engineering and here some soil samples are given and their…

Q: Crude oil of specific gravity 0.85 flows upwards at a volume rate of flow of 60 liters per second…

A:

Q: A symmetrical three hinged circular arch has a span of 16 m and a central rise of 4 m. It carries a…

A:

Q: Problem Two: Consider the cross-sectional shown in the figure below. The cross-section is reinforced…

A:

Q: If lateral supports are to be provided, calculate the biggest spacing to be specified so that the…

A: Given, beam CG of length 10 m specifications of the cross section are also given. Maximum bending…

Q: Problem No. 1 A copper rod of length L =18.0 in. is to be twisted by torques T (see figure) until…

A:

Q: concrete beam with balanced-stress ment. 1039. Design a reinto reinforcement that will resist a…

A:

Q: Problem 1: The bar shown is in equilibrium. Determine force P, T, and R. R 5m 5n 280N 3n 5m 3n 5m…

A:

Q: Question 5 (a) Estimate the depth of evaporation (in mm units) that can be expected to occur over a…

A: Solution Evaporation depth, E = Hn-Hg-Hs-HiρL(1+β) Where, Hn -Hg = available energy = 800 W/m2 = 800…

Unit Conversion

Standard units are also called SI units. SI units are used for measuring a physical quantity satisfying certain conditions. There are two types of units: fundamental units and derived units. Fundamental units are physical quantities that are independent, that is, they do not depend on other quantities like mass, length, or time. There are plenty of quantities in our lives which need to be measured and compared. Measuring is the comparison of a particular physical quantity with its reference value. A unit is a measure of a fixed physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.