Question 2 The following data relate to an injection moulding grade of a thermoplastic polymer. Determine whether this melt obeys the power law and if so, estimate the power law exponent n. Comment on your findings. Shear rate (s") Viscosity (Pa.s) 10 2590 100 2260 500 1370 1000 845 2000 525 5000 278 10000 175

Question 2 The following data relate to an injection moulding grade of a thermoplastic polymer. Determine whether this melt obeys the power law and if so, estimate the power law exponent n. Comment on your findings. Shear rate (s") Viscosity (Pa.s) 10 2590 100 2260 500 1370 1000 845 2000 525 5000 278 10000 175

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

This exercise requires showing the complete scanned strokes and procedures, adding it to a pdf document with evidence of all the exercises and the honesty letter. A Titanium specimen with a diameter of 0.8 [in] and 2.5 [in] in length is stretched in uniaxial tension. 1. What is the maximum elongation (DI) of the material. If the deformation is completely elastic? 2. What force is being applied Consider the material properties S_UTS=1205 [MPa]; Sy= 1075 [MPa]; E= 100 [GPa] in the following space write the values found as follows, do not forget the units (-0.5 pts if 4d units do not appear): ]; F= [];
Please answer within one hr i will give good rating.
Question 9 Answer the following questions. Show your work on a separate paper. Round your responses to 3 significant figures. Include appropriate units. Provide magnitude and direction where appropriate. The 4.5 Mg truck shown below collides with the 1.75 Mg car. After the collision, they move forward together. Answer the following questions. 30 km/h 10 km/h 38) What is the combined velocity of the truck and the car just after impact? Show your work. Solution Units Direction 3b) What is the coefficient of restitution of the impact? Show your work or justify your response on a separate piece of paper. Solution Units
Presented below are the quality ratings with regard to soil moisture availability. Erosion rating Moisture rating Erosion Rating MC (%) Rating Slope Slope rating Rating hazard class Low 1 0-5 4 0-5 1 Moderate 2 5-15 3 5-10 2 High 3 15-20 2 10-25 3 Very high 4 >20 1 >25 4 Quality ratings of three land units are tabulated below. Land quality rating Land unit Nutrient availability Trafficability 1 2 1 2 3 1 3 2 2 Additional characteristics of the land units areas follows: Land Permeability Land use M.C. Slope Clay V. Silt OM Structure % % Fine % % unit sand % 1 2 Slow Moderate Rangeland Arable 10 9 40% 10 30 4 blocky 18 8 30% 20 20 2 Coarse granular 3 Moderate to Settled 22 12 20% 15 50 3 Fine rapid granular Suitability Class Nutrient The suitability rating for land qualities for tomatoes and cabbage production is also indicated below; Suitability classes for Tomato production Trafficability Moisture Land Qualities Slope Erosion availability hazard S1 1 2 2 2 2 S2 2 3 3 2 S3 3 4 3 3 4 S4…
The elastic region of a materials stress strain graph is shown below. Determine the Modulus of Elasticity from the graph data then select the correct modulus in the choices below. 20,000,000 psi 30,000,000 psi 40,000,000 psi 5,000,000 psi