Question 2: Common Base For the amplifier circuit in Figure Q.1, the transistor parameters are Ica= 1.36 mA, B = 125, VBE = 0.7 V and VA = 0, 1) Draw the mid-frequency AC equivalent circuit of the amplifier. 2) Determine the amplifier input impedance, Zi and output impedance, Zo. 3) Determine the voltage gain, Av=VL/Vi 4) Determine the current gain, Ais=IL/IS C3 10 µF i 100 µF R2 24 k2 Rc 3.9 k2 R, 100 k2 RE 3.3 k2 RL 4.3 k2 Vị VL i, 100 sin ot uA C2 4.7 µF Vcc 10 k2 18 V Zo Figure Q.1

Question 2: Common Base For the amplifier circuit in Figure Q.1, the transistor parameters are Ica= 1.36 mA, B = 125, VBE = 0.7 V and VA = 0, 1) Draw the mid-frequency AC equivalent circuit of the amplifier. 2) Determine the amplifier input impedance, Zi and output impedance, Zo. 3) Determine the voltage gain, Av=VL/Vi 4) Determine the current gain, Ais=IL/IS C3 10 µF i 100 µF R2 24 k2 Rc 3.9 k2 R, 100 k2 RE 3.3 k2 RL 4.3 k2 Vị VL i, 100 sin ot uA C2 4.7 µF Vcc 10 k2 18 V Zo Figure Q.1

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

To keep inter stage loses to minimum in multistage amplifier, ................is required.
Class B Amplifier q1)If the input is 7.5Vp-p...DATA COLLECTION: What is the IL(peak)? a)7mA 6)mA 5)mA 4)mA q2) DATA COLLECTION: What is the Idc? a)3.84 b)4.82 c)3.82mA d)1.82mA q3)DATA COLLECTION: What is the input power in DC? Power input = 48.45mW Power input = 45.48mW Power input = 44.58mW Power input = 45.84mW q4) DATA COLLECTION: What is the output power in AC? a)18mW b)81mW c)11.8mW d)18.9mW q5)DATA COLLECTION: What is the power dissapated by each transistor? a)35.1mW b)53.1mW c)15.3mW d)13.5mW q6)DATA COLLECTION: What is the efficiency of class B amplifier? a)45% b)40% c)63% d)33% q7)
Describe two different methods for determining the stability of an amplifier.
This problem is AC analysis problem. DC analysis is not needed to answer the question. A) Convert this bias circuit into a bypassed common source amplifier that has an output across a load resistor (RL). To do this you should draw three capacitors on the figure below, an input voltage source, and any resistors you think that should be added. B) In the space below the figure, Draw the hybrid n model for this amplifier circuit including all voltages and resistors. Label Vi, Vgs, and vo on the model. Assume the capacitors you add act as short circuits at AC. Be sure to include resistors R1, R2, R3, R4, and RL in the hybrid pi model. > When you "verify" a mode of operation you will need to calculate all three voltages (Vc, V8, VE for BJTS and VG, Vs, Vo for MOSFETS) and show the correct two conditions are satisfied. > Assume Capacitors acts like open circuits at DC and short circuits for AC. > Assume the following: o Beta = 100 O VBE = 0.7 12V o V (Thermal) = 26 mV o V (Threshold) = 2V O…
Correct the sentence: The aim of using coupling in multistage transistor amplifiers is to transfer DC output of one stage to the input of the next .stage and to isolate the d.c. conditions of one stage from the next stage
(b) The multistage amplifier circuit of Figure Q.2(b) have the following parameters: Qı and Q2: B= 200, VBE = 0.7 V, VT = 26 mV , VA=∞ Given that Icọ1 = 2 mA and VCEQ1 = 2 V. (i) Determine the value for R84. List the assumption/approximation made in the analysis. (ii) Sketch and label the small-signal hybrid-t equivalent circuit at midband frequency range. (iii) Calculate the small signal hybrid-n model parameters: gm and ra for Qı and Then, determine Zi2 and Zo. VSI (iv) Find +15 V TU MA RBI 100 k2 UNIVERSITI { Rc 3.3 k2 RB3 10 kN IcQI Q2 C4 Qi VCEQI Ro TEO ► 50 k2 Rs 100 2 RL V. 10k2 RE 2 kN RB4 C3 Zi2 Z, Figure Q.2(b) AYSIA
Why do we need 3 types of cascaded amplifiers?
this question is analog electronics question
explain RC coupled amplifier in detail .
Show that series-Fed Class A Amplifier Efficiency is 25%?