Question 2:Calculate the required percentage form the following scrap, which would satisfy thefollowing composition for the production of casting billet-MS 70 (70% Cu- 30% Zn)%Cu-9058ChargeRed brass scrapMS 58%Zn1042

Given: Charge %Cu %Zn Red brass scrap 90 10 MS 58 58 42 To find: Required percentage of…

Question 2: Calculate the required percentage form following composition for the production Charge Red brass scrap MS.58 the following scrap, which would satisfy the of casting billet-MS 70 (70% Cu- 30% Zn) %Cu %Zn 10 42 :90 58

Question 2: Calculate the required percentage form following composition for the production Charge Red brass scrap MS.58 the following scrap, which would satisfy the of casting billet-MS 70 (70% Cu- 30% Zn) %Cu %Zn 10 42 :90 58

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Question One (Compulsory) Composition (atk Sn) 100 20 40 60 80 327C B00 300 Liquid 500 232C 400 200 183C 07.8 18.3 61.9 300 100- H200 100 BO 100 20 40 60 Pb) Compesition (wt% Sn) Figure 1: Lead -tin phase diagram Figure I above shows a lead-tin (alloy) phase diagram. Consider an alloy composition of 55 wt% Sn - 45 wt% Pb. Answer the following questions: (i) Name the phases present and their compositions in the alloy at 150°C. (ii) Describe the structural and composition changes in the alloy when it is cooled from 190°C to 20°C. (iii) What are the compositions of phases at the eutectic point and why is this point important for the alloy? (iv) Given that the average density of a phase is determined as Pa = 100 ,calculate the PA PB volume fractions of the phases at the given compositions and at 150°C. Take the densities of lead and tin as 11.34 g/cm' and 7.36 g/cm' while the mass fraction of a is 0.21. (v) Name and describe four industrial applications of lead-tin alloys. ta aroundu (3.)…
6) Horizontal centrifugal casting is used to make aluminum rings with length L= 5 cm, outside diameter do = 65 cm, and inside diameter d; = 60 cm. The density of aluminum is p = 2.7 cm3 cm³ a) Determine the rotational speed that will provide a G-factor = 60. b) Determine the centrifugal force when the cast is operating at the rotational speed.
Consider the casting in (Figure 1). Figure 20 mm 40 mm 120 mm 40 mm 1 of 1 Part A Determine the distance to the center of mass of the casting that is formed from a hollow cylinder having a density of 3.2 Mg/m³ and a hemisphere having a density of 3 Mg/m³. Express your answer to three significant figures and include the appropriate units. IN = μᾶ Value Submit Previous Answers Request Answer X Incorrect; Try Again Units < Return to Assignment Provide Feedback ?
QUESTION 14 Pieces thicker than 5.45mm are considered sheet. O True O False QUESTION 15 In sand casting, natural sands are less economical than synthetic sands. O True O False QUESTION 16 Typical sheet-metal thicknesses are between 0.15 mm and 7 mm. O True False
6.8 Suppose that a cast Al-1 wt% Si alloy, contains equilibrium Si particles 1 µm in diameter. This alloy is to be heat treated by first putting all of the Si particles back into solution. (a) Draw a set of schematic curves indicating what will happen during this process. Temperature °C (b) Indicate the initial conditions, the final conditions (once a new equilibrium is reached) and the boundary conditions during dis- solution. (c) Estimate how long the alloy should be held at 550°C so as to ensure that all of the Si is dissolved. Al-Si 1500 1300 1100 900 700 500 300 660.452°C 0 -(A1) 10 AI 12.6 10 20 20 30 30 Atomic Percent Silicon 40 50 Thom L 60 Them 577+1°C 40 50 60 Weight Percent Silicon 70 70 80 80 90 90 100 1414°C (Si)- 100 Si
Volume of a cube of side / and volume of a sphere of radius rare equal. Both the cube and the sphere are solid and of same material. They are being cast. The ratio of the solidification time of the cube to the same of sphere is 3. 6. 4T (a) 6. 4T (b) 6. 3. 4 4T (c) 6. (d) 6.
Q1. Fill the blanks 1- The formation of metal alloys system consist of ,1..,2...,3...,4...,5..,6... 2-The cooling curve types due to solidification state of alloy metal elements are, 1..,2...,3...,4... .....
15) Use fundamental principles to argue briefly that the heat capacity at constant pressure is greater than the heat capacity at constant volume for a gas. ( Hiuti Try (st Taw) 16) Draw a PUT surtace aud in de'cate the regions where two phases cuexist, aud labe( the axes
a) Briefly explain what is meant by the following: i. Cold-working, ii. Hot-working b) Briefly explain the following as applied to heat treatment of plain carbon steels: i. Hardening ii. Annealing iii. Tempering iv. Normalizing c) Estimate the recovery temperature for a cold worked sheet metal if its melting temperature is taken as 1080 degrees Celsius
1) Draw the iron-Fe;C phase diagram. Consider 0.25 and 1.1 wt% C steel alloy. It is cooled slowly from atemperature within austenite phase to room temperature. Show a) microstructure at 1000 °C b) microstructure at 730°C c) microstructure at 715°C and d) microstructure at room temperature e) What do you say about mechanical properties of these alloys, depending on their microstructure at room temperature?
flו. 3D) امتحان شهري.pdf 1. A square section riser be designed for a sand-casting mold. The casting itself is a quarter-cylinder with a diameter of 12cm and a length 20cm. The total solidification time for this casting = 0.9 min. The square for the riser will have a height-to-width ratio of 2.0. Determine the dimensions of the riser so that it is total solidification time = 1.2 2. A mold sprue is 180 mm long, the cross-sectional area at its base is 2.4 cm?. The sprue feeds a horizontal runner leading into a mold cavity whose volume is 1600 cm?. Determine, volume rate of flow and time to fill the mold.