Question-1(CLO 1,2) A hollow bronze shaft of 3 in. outer diameter and 2 in. inner diameter is slipped over a solid steel shaft 2 in. in diameter and of the same length as the hollow shaft. The two shafts are then fastened rigidly together at their ends. For bronze, G = 6 x 10° psi, and for steel, G = 12 × 10° psi. What torque can be applied to the composite shaft without exceeding a shearing stress of 8000 psi in the bronze or 12 ksi in the steel? Hollow Bronze Steel Core D = 3 in, d = 2 in D = 2 in

Question-1(CLO 1,2) A hollow bronze shaft of 3 in. outer diameter and 2 in. inner diameter is slipped over a solid steel shaft 2 in. in diameter and of the same length as the hollow shaft. The two shafts are then fastened rigidly together at their ends. For bronze, G = 6 x 10° psi, and for steel, G = 12 × 10° psi. What torque can be applied to the composite shaft without exceeding a shearing stress of 8000 psi in the bronze or 12 ksi in the steel? Hollow Bronze Steel Core D = 3 in, d = 2 in D = 2 in

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Part A The solid shaft cross-sections shown are subjected to the externally applied torques shown. Compare the corresponding shear stresses developed in each shaft at point P. P P 2 T Rank the solid shafts from the largest shear stress at P to the smallest shear stress at P. (For example, 4> 3 = 1 > 2). 0.5 T
Question (1): A stepped shaft ABCD consisting of solid circular segments is subjected to three torques, as shown in the figure. The torques have magnitudes 12.5 kips. in., 9.8 kips, in., and 9.2 kips. in. The length of each segment is 25 in. and the diameters of the segments are 3.5 in., 2.75 in., and 2.5 in. The material is steel with shear modulus of elasticity G = 11.6 x 103 ksi.(a) Calculate the maximum shear stress Tmax in the shaft. (b) Calculate the angle of twist (pp (in degrees) at end D. 13.5 in. 12.5 k-in. -25 in.- B 9,8 k-in. 12.75 in. -25 in.- 9.2 k-in. 12.5 in. c t -25 in.-
Please answer complete
3. 15/16-inch-wide key has a depth of 5/8 in. It is 12 inches long and is to be used on a 200 hp, 1160 RPM, squirrel cage induction motor. The shaft diameter is 3 7/8 inches. The maximum direct shearing stress on the key, considering the effect of the keyway.
Problem 5 only, solve carefully, include the units in every step and draw the diagram. Thanks! A hollow shaft transmits 10 kW and running at 650 rpm with a shearing stress of 55 Mpa. The outside diameter is 1.2times that of the inside diameter. Find the inside and outside diameters in mm.
1. A 50-mm diameter solid shaft, with a length of 1 meter, is supported at one end and free in the other end. Determine the maximum allowable torque for each material if the angle of twist is not to exceed 6º. Remember to consider both the maximum shear stress and the angle of twist. MATERIAL MODULUS OF RIGIDITY MAXIMUM SHEAR STRESS TORQUE Aluminum 26 GPa 207 MPa Steel 79 GPa 75 MPa Titanium 44 GPa 760 MPa
400 lb-in. 1200 lb-in.. Specifications: Shafts AB, BC, CD are solid material. 500 lb-in., B AB=0.6 in. C dsc-0.75 in. dcp = 0.9 in. Determine: a) The shaft section in which the maximum shear stress occurs and the magnitude of the stress. Now consider that the shaft is tubular with a 0.300 inner diameter. Determine: b) The shaft section in which the maximum shear stress occurs and the magnitude of the stress.
1. The hollow steel shaft (G=12 000000 Psi) must transmit a torque of 300000 lb-in. The total angle of twist must not exceed 3 degrees per 100 ft. the maximum shearing strength must not exceed 16000 Psi. (a) Find the inside diameter "d" if the outside diameter is equal to 12 inches. (b) Find the maximum torsional shear stress and (c) Find the maximum torsional shear strain.
Member ABCD is a hollow circular steel shaft with a 4 inch outer diameter and a 3 inch inner diameter. It is rigidly attached to the wall at A. Externaly applied torques are TB of 1338 lb-ft, Tc of 1117 lb-ft, and TD of 884 lb-ft. Firstly obtain the internal torque generated, then calculate and input the maximum shear stress in section BC of the shaft: (f v max) = ___________ lb/in.2. Pay attention to unit conversion and calculate your answer to 1 decimal place.
Question 4. The shaft is made from a solid steel section AB and a tubular portion made of steel and having a brass core. If it is fixed to a rigid support at A, and a torque of T 50 kN.m is applied to it at C, determine the angle of twist that occurs at C and compute the maximum shear stress and maximum shear strain in the brass and steel. Take Gst 115 GPa, Gbr 56 GPa. 3 m %3D 2 m 100 mm 50 mm T= 50 kN. m
Question 2 A composite shaft is comprised of a solid inner rod (shaft 1) made of a steel with an elastic modulus of 210 GPa, diameter of 70 mm, and length of 100 mm, and a hollow outer shaft (shaft 2) made of the aluminium with an elastic modulus 80 GPa, outer diameter of 100 mm, inner diameter of 80 mm, and a length of 100 mm that are rigidly attached to one another on both ends. The composite shaft is designed to absorb 150 joules of energy for deformation within its linear elastic limit upon application of an axial load onto a collar attached to its lower end. Determine the stresses induced in shafts 1 and 2, magnitude of the forces acting on shafts 1 and 2, and the total force acting on the composite shaft for the cases of: (i) A gradually applied load. (ii) A suddenly applied load. (iii) A mass that is dropped onto the collar from a height of 250 mm.
Need only handwritten solution only (not typed one).