Question 15 Increasing the concentrations of the reactants in a chemical reaction increases the rate of reaction because the: collisions become more effective. frequency of collisions increases. average kinetic energy increases. activation energy decreases.

Q: (1) Explain the following terms: i) Slack and Raw wax

A: Slack Wax: It is yellow to dark in color. It is also known as crude paraffin wax. It is separated…

Q: Is pinch point always located at the feed stage?

A: The location of the pinch point is to be mentioned.

Q: Mention some key considerations during installation of a cyclone seperator?

A: Cyclonic separation is a means of separating different liquid phases, or, separating particles from…

Q: Explain RECYCLE AND BYPASS?

A: To design a new process or analyze the existing one, material balance, energy balance equations at…

Q: A machine rotates at 8800 rpm and decelerates at 95 rad s^-2 . Find how long it takes the machine to…

A: The objective of the question is to find out the time it takes for the machine to stop from its…

Q: Given a 35% mixture, what will be the time of flow? * O 43.5% O 41.5% O 6.6% 6.5%

A:

Q: Illustrate and discuss the process flow for the manufacture of porcelain

A: Solution-Step:  (a) Component needed(i) Feldspars K2O.Al2O3.6SiO2 & Na2O.Al2O3.6SiO2(ii) Quartz…

Q: Describe 1st angle and 3rd angle Projections?

A: 1. First Angle Projection : In the first angle projection, we can placed the object in the 1st…

Q: For fractional distillation write explain and draw a schematic neat diagram with all labeled parts…

A: Fractional distillation is a type of distillation which involves the separation of miscible liquids.…

Q: Draw a graph and explain the variation of pressure drop with time in a compartmented baghouse.

A: To ensure the system's successful operation at all times, a variety of variables must be managed…

Q: Give an example of a hybrid system that involves recycle.

A: An example of a hybrid system that involves recycle is to be mentioned.

Q: Draw another schematic drawing as well as show dead zones

A: A reactor dead zone is a poorly mixed area that affects the effective volume and overall efficiency…

Q: Present one example depicting the impact of instrumention on one or more process variables.

A: Consider a Water tank with a level controller. Here consider the different process variables. Input…

Q: 3 How many lbf are needed to accelerate 2 lbm at 1 ft/² ?

A: given = mass = 2 lbmacceleration = 1 ft/s2to find = how many lbf are needed

Q: Draw Resource Pyramid and discuss its components

A:

Q: If the time of flow of the given mixture is 50 seconds, what is the composition of the mixture? * O…

A:

Q: Explain the friction between the mater (soled with soled, liquid with liquid)?

A: Motion: Motion is the phenomenon in which an object changes its position over time. Motion is…

Q: Explain Process of extraction oil lubricant about description and conditions process

A: A lubricant is a substance that helps to reduce friction between surfaces in mutual contact, which…

Q: For multi-component systems, Underwood Equations gives OL Minimum Trays O II Minimum Strip O II…

A: Distillation is a separation process in which light hydrocarbon is separated from heavy hydrocarbon…

Q: How to calculate pressure drop in Gas pipe , formula ,

A: When gas flows in pipes, the pressure drop is caused due to following reasons:Friction in the…

Q: Compression Moulding of plastic  can you please write the all procees and advantage and…

A: Compression moulding is a process to mould plastics into the desired product. This method uses…

Q: The following are not commonly made from composites: Select one: a. Desks b. Canoes c. Bridges d.…

A: Ans.  Composites is the material that are made up of two or more materials. Which on combining they…

Q: What is the most common method used to separate two fluid phases?

A: The most common method which can separate two fluid phases is to be mentioned.

Q: Explain and describe possible factors that may affect fluidization.

A: Fluidization parameter (calculated via inlet air drift fee and rotor speed), stress distinction over…

Q: Discuss Lever-Operated Knapsack Sprayer

A:

Q: wire 10 m long has a cross-sectional area 1.25 x 10-4 m2. It is subjected to a load of 5 kg. If…

A: As we know  Youngs modulus = stress/strain  Stress= force/area  Strain= change in length /initial…

Q: 13. Draw the P-x-y diagram, write the main futures in the diagram

A: It is required to draw the P-x-y diagram and explain the main features of the diagram.

Q: Given a 60% mixture, what will be the time of flow? * О 90% O 80% O 48% О 45%

A:

Q: A high degree of cross-linking increase the amount of movement of the

A:

Q: Make a research on the fractional column

A:

Q: Distillation is an essential operation used commonly for the separation of materials in process…

A:

Q: What is the method or heory that the laborator device depends on in measuring potassium?

A:

Q: increasing of the column pressure, results in

A: Column pressure is the pressure of liquid due to its height. Pressure has direct effect on the…

Q: wife State the limitations of the emf series and the advantages of galvanic series for an engineer?

A: The limitations of emf series and advantage of galvanic series are to be outlined.

Q: Define about compression ratio ?

A: The compression ratio is to be defined.

Q: For each of the following scenario, determine which metal and or metal alloy material is best suited…

A:

Q: Differentiate between Variable head meter and variable area meter used in Chemical processing

A: Flow meters are used in chemical processes to accurately measure fluid flow. Variable Head Meters…

Q: Write detailed short note on PAC.

A: The objective of this question is to provide a detailed explanation of PAC, which stands for…

Q: Q1/ A liquid is pumped in streamline flow through a pipe of diameter d. At what distance from the…

A: Solving Q1