Question 15 IH device uses the following scale for personal noise to comply with the OSHA PEL-TWA Select one: O a. B-scale Ob. A-scale Oc. C-scale Od. A, B and Hertz scale Oe. B, C and Hertz scale

Q: If the value of the damping ratio or damping factor is 1.5, then the system is an overdamped system.

A: An overdamped system is a system which slowly reaches to the equilibrium state

Q: When using vertical coding, what components are required and how is the control unit constructed?

A: Vertical micro coding, also recognized as vertical microprogramming, is a method used in computer…

Q: Why do APC ferrules have a lower reflectivity than UPC ferrules

A: APC ferrules have a lower reflectivity than UPC ferrule will be explained :

Q: A device that converts one type of signal into another is called Transducer why?

A: Given that: A device that converts one type of signal into another is called Transducer why?

Q: least ten basic method of troubleshooting audio sy

A: Let see the basic methods of troubleshooting the audio system. 1) The first thing to do is to shut…

Q: If the input frequency applied to given system is 640 KHz then the output frequency will be. kHz.…

A: Introduction :

Q: H.W4 The diode in the single-phase half wave rectifier has a reverse recovery time of tr 150sec and…

A: the solution is an given below :

Q: IC in a DAC acts as an amplifier to amplify the analog output voltage.

A: IC stands for Integrated circuits.

Q: With internal detectors, what is the most prevalent source of noise?

A: The principal causes of internal detector noise in an optical detector With signal defined as the…

Q: IC in a DAC acts as an amplifier to amplify the analog output voltage.

A: High current voltage is the output that can be received from DAC.

Q: 91 a, b→c 92

A:

Q: Step Response From: r To: y 0.9 System: 1OTransfer, 2y 0.8 System: 1OTransfer,2y VO: r to y Peak…

A: ANSWER: Lead-lag Controller: C(s) =1+aTs1+Ts       [a>1] C(s) =Kc(s-z0)s-p0

Q: 20. What are the signals used in input control signal & output control signal?

A:

Q: The definition of Vertical Micro Code

A: The definition of Vertical Micro Code: The micro-operations in vertical microcode are organised…

Q: SLA and HDD differ in these ways.

A: SLA (Service Level Agreement) and HDD (Hard Disk Drive) are two separate terms that are frequently…

Q: How is a vertical-coding control unit assembled?

A: The assembly of a vertical-coding control unit is a fascinating process worth exploring. This…

Q: What is used to provide noise immunity to the system by adding some redundancy such as block…

A: In computing, a linear feedback shift register (LFSR) is a shift register whose input bits are a…

Q: EDIF stands for(a) electronic device interchange format(b) electrical design integrated fixture(c)…

A: EDIF stands for Electronic Design Interchange Format.

Q: please create the schematic on KiCad software for this circuit

A:

Q: Why do APC ferrules have a lower reflectivity than UPC ferrules?

A: The reflectance of a connection is the amount of light that is reflected back up the fiber toward…

Q: What makes a vertical-coding control unit?

A: Vertical coding in control units refers to a methodology employed in computer architecture for micro…

Q: Calculate the value of the multiplier resistor for a 10 V rms ac range on the (30 marks) voltmeter…

A: Hi. Check below the calculation for value of the multiplier resistor for a 10V rms

Q: How are vertical-coding control units built?

A: Vertical-coding control units are an essential component in various technological systems. These…

Q: Question 777 electric     LTspice/ circuit please help Full explain this question and text typing…

A: Amplifier: Amplifier is the generic term used to describe a circuit which produces and increased…

Q: let list=1200 element. Note: java programmimg, use given code. 3a. Use the binary search  3b. Use…

A: Note: I am running the program on a list of size 20 for the clear output. You can set the size to…

Q: Design 4 bit Flash ADC, with Vref = 12 v and Vin = 7.5 v.

A: Given data is shown below: Design 4 bit Flash ADC, with Vref = 12 v and Vin = 7.5 v.

Q: CD Track Spiral and Track Enlargement

A: Given : -   CD track spiral and track enlargement  as shown in figure given    Need to explain the…

Q: A microcontroller DAC uses a 5 volt reference and 12 bit resolution. What code should be written to…

A: 1) DAC uses 5V reference and 12 bit resolution 12-bit can accomodate FFF in hex = 4096 in decimal…

Q: A narrow band-reject filter is commonly called as O notch filter O delay filter O band stop filter O…

A: A narrow band reject filter possesses high value quality factor.

Q: What is the main source of internal detector noise ?

A: sources of internal detector noise

Q: When the input device of the instrumentation system has undesired signal (noise), the noise must…

A: Here in this question we have asked if the input device of the instrumantation system has noise.then…

Q: what is the main sources of internal detector noise?

A: the main sources of internal detector noise

Q: Distinguish between a signal element and a data element.

A:

Q: What is the most common cause of noise in internal detectors?

A: Internal noise is also called psychological noise.