Question 11: A horizontal force F is applied at the centre of mass of a cylindrical object of mass m and radius R, perpendicular to its axis asshown in the figure. The coefficient of friction between the object and the ground is. The centre of mass of the object has an acceleration a. Theacceleration due to gravity is g. Given that the object rolls without slipping, which of the following statement(s) is (are) correct?a. For the same F, the value of a does not depend on whether the cylinder is solid or hollowb. For a solid cylinder, the maximum possible value of a is 2gc. The magnitude of the frictional force on the object due to the ground is always mgd. For a thin-walled hollow cylinder, a = F/2m

Answered: Image /qna-images/answer/99501682-d34e-4524-966b-bf668946d844.jpg

Answered: Question 11: A horizontal force F is…

Similar questions

A bicycle mechanic is checking a road bike's chain. He applies force FF = 21 NN to a pedal at the angle shown in (Figure 1) while keeping the wheel from rotating. The pedal is 17 cmcm from the center of the crank; the gear has a diameter of 16 cmcm. What is the tension in the chain?
A 1.00-m-diameter solid sphere can be rotated about an axis through its center by a torque of 18 m N, which accelerates it uniformly from rest through a total of 190. revolutions in 20.0 s. (How do i find the mass of the sphere and what equations/ steps can I use to find it?)
A uniform disk of radius 0.489 m and unknown mass is constrained to rotate about a perpendicular axis through its center. A ring with the same mass as the disk is attached around the disk's rim. A tangential force of 0.211 N applied at the rim causes an angular acceleration of 0.115 rad/s2. Find the mass of the disk.
Suppose you exert a force of 167 N tangential to a 0.255 m radius 75.0 kg grindstone (a solid disk). (Give your answers to at least 2 decimal places.) (a) What torque (in N m) is exerted? (Enter the magnitude.) 42.585 N.m (b) What is the angular acceleration (in rad/s²) assuming negligible opposing friction? (Enter the magnitude.) 2.44 X rad/s² (c) What is the angular acceleration (in rad/s²) if there is an opposing frictional force of 22.6 N exerted 1.75 cm from the axis? (Enter the magnitude.) rad/s²
A disk with uniform density and radius 0.551 m used to weigh 20.22 kg, but then a hole was punched out. The black arrow in the image above shows the axis of rotation. The hole has radius 00753 m, and has its center 0.103 m away from the center of the disk. What is the înoment of inertia of the disk with a hole? (Hint: only a scientist could call a hole negative mass! Find the mass taken away based on hole size and disk) Answer: Check Choose...
You have a grindstone (a disk) that is 77.0 kg, has a 0.400-m radius, and is turning at 89.0 rpm, and you press a steel axe against it with a radial force of 16.0 N. (a)Assuming the kinetic coefficient of friction between steel and stone is 0.50, calculate the angular acceleration (in rad/s2) of the grindstone. (Indicate the direction with the sign of your answer.) rad/s2 (b)How many turns (in rev) will the stone make before coming to rest? rev
A centrifuge rotor rotating at 9300 rpm is shut off and is eventually brought uniformly to rest by a frictional torque of 1.66 m⋅N. If the mass of the rotor is 4.58 kg and it can be approximated as a solid cylinder of radius 0.0440 m, through how many revolutions will the rotor turn before coming to rest? Express your answer to three significant figures. How long will it take? Express your answer to three significant figures and include the appropriate units.
A 23 cm wrench is used to generate a troque at a bolt. a force of 51 N is applied at the end of the wrench at an angle of 51° to the wrench. The torque generated at the bolt is? Answer in N.m
A disk with uniform density and radius 0.551 m used to weigh 20.22 kg, but then a hole was punched out. The black arrow in the image above shows the axis of rotation. The hole has radius 00753 m, and has its center 0.103 m away from the center of the disk. What is the înoment of inertia of the disk with a hole? (Hint: only a scientist could call a hole negative mass! Find the mass taken away based on hole size and disk) Answer: Check Choose...
A 0.75-m-diameter solid sphere can be rotated about an axis through its center by a torque of 11.8 m∗N which accelerates it uniformly from rest through a total of 150 revolutions in 15.0 s. What is the mass of the sphere? (Please list step by step for me to follow along and each equation needed to be used).
A model airplane with mass 0.749 kg is tethered to the ground by a wire so that it flies in a horizontal circle 30.0 m in radius. The airplane engine provides a net thrust of 0.807 N perpendicular to the tethering wire. (a) Find the magnitude of the torque the net thrust produces about the center of the circle. N. m (b) Find the magnitude of the angular acceleration of the airplane. rad/s2 (c) Find the magnitude of the translational acceleration of the airplane tangent to its flight path. m/s2
Problem 2. Three forces are applied to a disk of radius 0.35 m and mass 2.5 kg, as shown in figure below. One force is perpendicular to the rim, one is tangent to it, and the other one makes a 40.0° angle with the radius. The moment of inertia of a disk about its center is I = (1/2)MR². (a) What is the net torque on the disk due to these three forces for an axis perpendicular to the disk and passing through its center? (b) What is the angular acceleration of the disk? 11.9 N 0.350 m 40.0° 14.6 N 8.50 N

SEE MORE QUESTIONS