Question (1): Two cylindrical rods, AC made of aluminum and CD made of steel, are joined at C and restrained by rigid supports at A and D. For the loading shown and knowing that Ea = 10.4 × 29 x 106 psi, determine (a) the reactions at A and D, (b) the deflection of psi and Es = 106 point C A 8 in.10 in.10 in. -10 in B 18 kips 1in. diameter C 14 kips D 1-in. diameter

Question (1): Two cylindrical rods, AC made of aluminum and CD made of steel, are joined at C and restrained by rigid supports at A and D. For the loading shown and knowing that Ea = 10.4 × 29 x 106 psi, determine (a) the reactions at A and D, (b) the deflection of psi and Es = 106 point C A 8 in.10 in.10 in. -10 in B 18 kips 1in. diameter C 14 kips D 1-in. diameter

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

please answer number 4.Mech 222- mechanics of deformable bodies:please give detailed solutions and correct answers.i will report to bartleby those tutors who will give incorrect answers.
The rod ABC is made of an aluminum for which E = 71.15 GPa. Knowing that P=10.2 kN and Q=51.62kN, determine the deflection (in um) of point B y=0.46 and z=0.56. Round off the final answer in four decimal places.
A 22MM DIAMETER ROD BC IS ATTACHED TO THE LEVER AB AND TO THE FIXED SUPPORT AT C. LEVER AB HAS A UNIFORM CROSS SECTION 9.5 MM THICK AND 25 MM DEEP. FOR THE LOADING SHOWN, DETERMINE THE DEFLECTION OF POINT A. USE E = 200 GPA AND G = 112 MPA. 360 N 500 mm 250 mm B
16 The length of the 32-in.-diameter steel wire CD has been adjusted so that with no load applied, a gap of in. exists between the end B of the rigid beam ACB and a contact point E. Knowing that E = 29 × 106 psi, determine where a 50-lb block should be placed on the beam to cause contact between B and E.
The steel frame shown has a diagonal brace BD with an area of 1612 sq.mm. Determine the largest allowable load P (in N) if the change in length of member BD is not to exceed 1.27 mm. Use x = 4.4m, y = 5.76m, and E = 197 Gpa. Express your answer in four decimal places. ... B D X.
Two rods AB and BC of the same flexural rigidity EI are welded together at B. For the loading shown,determine (a) the deflection of point C, (b) the slope of member BC at point C. (Use energy methods)
1. A rod consisting of two cylindrical portions is restrained at both ends. Portion AB has a diameter of 1.25 in. and is made of steel (E, = 29 × 10° psi, and a = 6.5×10/°F). Portion BC has a diameter of 2.25 in. and is made of brass (Eb = 17 × 10° psi, , = 10.4x10/°F). Knowing that the rod is initially unstressed, determine (a) the normal stresses induced in portions AB and BC by a temperature rise of 65°F, (b) the corresponding deflection of point B. Ans: OAB = 22.17 ksi (C), oBC = 6,84 ksi (C), &B = 4.10 ×10³ in () steel brass 12 in 15 in
2. Two cylindrical rods, AC (made of steel, E, = 200 GPa), and CE (made of brass, Eb = 105 GPa) are joined at C and restrained by rigid supports at A and E. The diameter of the steel rod is 40 mm. The diameter of the brass rod is 30mm. The applied forces are PB = 60 kN and Pp = 40 kN. Determine: (a) the reactions at A and E, (b) the deflection of point C relative to point A. Ans: RA = 62.8 kN +, Re = 37.2 kN –, &c = 0.0463 mm →) B C D E Pp 180 mm 120 mm 100 mm 100 mm
50 N -450 mm SOLUTION 100 N 450 mm 150 N B 50N PROBLEM 4.13 The maximum allowable value of each of the reactions is 180 N. Neglecting the weight of the beam, determine the range of the distance d for which the beam is safe. 100N IOON, et -d-4 +0.45m 150N 0.45'm ΣF = 0 B =0 3*
The rod ABC is made of an aluminum for which E = 71.86 GPa. Knowing that P = 7.72 kNand Q = 48.58 kN,determine the deflection (in μm) of point A if y = 0.48 and z = 0.59. Round off the final answer in three decimal places.
PROBLEM 4.The beam AB consisting of a cast iron plate of uniform thickness, b, and length, L, is to support the distributed load w(x) shown a) Knowing that the beam is to be of constant strength (fully stressed beam), express h in terms of x, L and ho. b) Determine the smallest value of ho if L=800 mm, b=25 mm, wo=300 kN/m and oall=200 MPa. w-=WoCos(ITX/2L) A ho B