2.75 plz 2.75 The plastic block shown is bonded to a rigid support and to a verti-cal plate to which a 55-kip load P is applied. Knowing that for theplastic used G = 150 ksi, determine the deflection of the plate.3.2 in.2.76 What load P should be applied to the plate of Prob. 2.75 to producea 16-in. deflection?2.77 Two blocks of rubber with a modulus of rigidity G = 12 MPa arebonded to rigid supports and to a plate AB. Knowing that c = 100 mmand P = 45 kN, determine the smallest allowable dimensionsa and b of the blocks if the shearing stress in the rubber is not toexceed 1.4 MPa and the deflection of the plate is to be at least 5 mm.4.8 in.2 in.Fig. P2.75

Answered: determine the deflection of the plate.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The plastic block shown is bonded to a rigid support and to a vertical plate to which a 55-kip load P is applied. Knowing that for the plastic used G= 150 ksi, determine the deflection of the plate
The rigid bar AD is supported by two steel wires of -in. diameter (E = 29 x 10 psi) and a pin and bracket at D. Knowing that the wires were initially taut, detemine (a) the additional tension in each wire when a 120-1b load P is applied at B. (6) the corresponding deflection of point B.
Prob.2: [2.24] Each of the links AB and CD is made of aluminum (E = 75 GPa) and has a cross-section area if 125 mm². Knowing that they support the rigid member BC, determine the deflection of point E. |A P = 5 kN 0.36 m E |B -0.44 m 0.20 m
A 2 m Steel: E = 200 GPa В 50 kN 3 m C 2.5 m Brass: E = 105 GPa 9.18 The 36-mm-diameter steel rod ABC and a brass rod CD of the same diameter are joined at point C to form the 7.5-m rod ABCD. For the loading shown and neglecting the weight of the rod, deter- mine the deflection of (a) point C, (b) point D. V100 kN Fig. P9.18
Fbd ,formula and calculation should be included. Please work it fast without wasting a time. 1)The rod ABC is made of an aluminum for which E = 70 GPa. Knowing that P = 9 kN and Q = 14 kN, determine the deflection of: (a) Point A, (b) Point B. Consider upward to be positive.
PLEASE ANSWER NUMBER 1.MECH 222-MECHANICS OF DEFORMABLE BODIES: PLEASE GIVE DETAILED SOLUTIONS AND CORRECT ANSWERS. I WILL REPORT TO BARTLEBY THOSE TUTORS WHO WILL GIVE INCORRECT ANSWERS.
Rigid bar ABC is supported by pin-connected bar (1). Bar (1) is 1.625 in. wide and 1.125 in. thick, and made of aluminum that has an elastic modulus of E= 10,200 ksi. Assume that a = 21 in., b = 36 in., c = 15 in., and d = 26 in. Determine the maximum magnitude of load P that can be applied to the rigid bar without causing member (1) to buckle. A P Answer: P = i a D (1) b M L B lb
Portion BC of the rod ABC are made of an aluminum for which E= 70 GPa and portion AB is made of steel for which E = 200 GPa. Given: P = 9 kN, a = 0.6 m, b=0.7 m and the diameter of rod AB is c = 36 mm, (a) Determine the value of Q so that the deflection at A is zero (b) The corresponding deflection of point B 60-mm diameter
3(a). Both portions of the rod ABC are made of an aluminum for which E= 60 GPa. Knowing that the magnitude of P is 3 kN, determine (a) the value of Q so that the deflection at A is zero, (b) the corresponding deflection at B. Figure 3 1.5mm diameter 1.0⁰m 50-mm diameter WSTE
The plastic block shown is bonded to a fixed base and to a horizontal rigid plate to which a force P is applied. Knowing that for the plastic used G = 55 ksi, determine the deflection of the plate when P = 11 kips. The deflection of the plate is in.
2.15 A single axial load of magnitude P = 58 kN is applied at end C of the brass rod ABC. Knowing that E = 105 GPa, determine the diam- eter d of portion BC for which the deflection of point C will be 3 mm. 30 mm 1.2 m Fig. P2.15 B -0.8 m Note:- • Do not provide handwritten solution. Maintain accuracy and quality in your answer. Take care of plagiarism. • Answer completely. • You will get up vote for sure.
Please answer it with full explanation otherwise i will.......

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS