Question 1 The following date pertains toa single phase motor: Number of poles = 4 Supply voltage = 110 V Rated output = 125 w Slip at rated output = 6% Total copper loss at full load = 25 W Rotational losses = 25 W Calculate the full-load efficiency and the rotor coper loss caused by the backward field. [14.94 W, 78.12%]

Question 1 The following date pertains toa single phase motor: Number of poles = 4 Supply voltage = 110 V Rated output = 125 w Slip at rated output = 6% Total copper loss at full load = 25 W Rotational losses = 25 W Calculate the full-load efficiency and the rotor coper loss caused by the backward field. [14.94 W, 78.12%]

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

An increase in the torque angle a results in: O A. No change in the induced torque O B. Decreasing the induced torque O C. Decreasing the load on the synchronous motor D. None of the other choices are correct O E. Increasing the induced totque
Solve it quickly please
DC/AC MOTOR (UPVOTE WILL BE GIVEN. PLEASE WRITE THE COMPLETE SOLUTIONS LEGIBLY. NO LONG EXPLANATIONS NEEDED. ANSWER IN 2 DECIMAL PLACES. BOX THE FINAL ANSWER.)
Q2] Fill in the blank (9 Marks) 1-The current drwan by the armature of D.C. motor is directly proportional to 2- The speed of a D.C. shunt-wound motor will shunt field regulator is increased. 3- The synchronous speed of a three-phase induction motor is number of pairs of poles. Rotor copper losses Rotor input power in induction motor = 5- A 4-pole three-phase induction motor has a synchronous speed of 25 r.p.s. The frequency of the supply to the stator is_ Hz. 6- The power input to a mains transformer is 200VA. If the primary current is 2.5A, the secondary voltage is 2V and assuming no losses in the transformer, the turns ratio step down. is 7- A 200kVA transformer has an iron loss of 1 kW and full load cu loss of 2 kW. Its load kVA corresponding to maximum efficiency is kVA. 8- If cu loss of a transformer at 7/8th full load is 4900 W, then its full-load cu loss would be watt. 4- if the value of resistance of the proportional to the 9- The slight curvature at the lower end of the open…
An 8-pole wave wound dc shunt generator is supplying 295 A to load. The field current of generator is 5A. The current parallel path is
10
Starting methech speed motor. we use and Control poly phase Induction
2) A large 3-phase, 4000 Va (phase to phase), 60 Hz squirrel-cage induction motor draws a current of 385 A/phase. The total active power at the stator input terminals is 2344 kW, when operating at full load. The corresponding speed is accurately measured and found to be 709.2 r/min. The stator is connected in wye and the resistance between two stator terminals is 0.10 Q. The total iron losses are 23.4 kW and the windage and friction losses are 12 kW. Calculate the following: c) The total 1²-R losses in the rotor d) The load mechanical power (kW), torque (kN•m), and efficiency. S = Va · V3 - I S= Vy•3·I %3D
three phase 400v (line voltage) 60 hz 6 pole star connected snkron generator per phase .It has 2 ohm synchronous reactor. the armature current of the generator at full load is 64 A with a power factor of 0.95 back. this generator has 2kW rotation loss and 1.6 kW core loss at full load. the excitation current is set to be 400 V when the generator is idle. generator current with 0.95 back power factor at full loadA) find the rotating field current of the generatorb) find the mechanical speed of the generatorc) What is the output voltaged) find the yielde) calculate voltage regulation