QUESTION 1 The diagram in fig 2, below shows a sequential circuit with inputs X1 and X2 and output Y. Using the waveforms of the clock, inputs and outputs W1, W2. W3 and W4, answer the following questions; i. what type of triggering method has been employed in the circuit? ii. how many clock cycles have been represented in the timing diagram? iii. choose the correct timing diagram of the output “Y”, from the waveforms W1, W2, W3, W4. Show all relevant steps used to obtain results

Q: If the input boardClock is connected to PIN_N5, find (a) LPM_MODULUS and (b) the minimum width of…

A: The DE10-Lite board has three clocks that can be seen in the table below: We need a clock of 2.5…

Q: When comparing the efficiency of full-wave and half-wave rectifiers, one of the following statements…

A:

Q: 1.A. What is the primary advantage of measuring a voltage with an oscilloscope verses using a…

A: As per our guidelines we are supposed to answer only first 3 subparts. Kindly repost the other parts…

Q: 4. The problems are: A circuit including three kinds of storage elements is shown in Figure 1. A:…

A: As per the guidelines, I am solving the first question (A). Please post the next question separately…

Q: CIk R A S R В B A- y

A: According to the given question, it is required to determine the state table and state diagram of…

Q: Identify the component which is not available in digital Voltmeter? a. Clock generator b. ADC c.…

A: We need to select component which is not inside the digital voltmeter .

Q: ii) Find QA, QB and Qc at each time interval and complete the timing diagram attached below. iii) If…

A: According to the question, we need to find QA, QB, QC for the given diagram as shown below,

Q: 01: Draw ladder program for system that will carry out: Switch on an output for the duration of the…

A:

Q: In HDB3, If the number of non-zero pulses is even, the format used is a. V000 b. B00V c. V00B d.…

A: The HDR-3 is HIgh Density Bipolar 3 Zero Coding.It is more conservative than other coding methods

Q: A speedometer is connected in an automobile system to measure the speed. The meter reads 120.8 rpm…

A: In this question we need to choose a correct option

Q: Q2) For the set of input waveforms in Figure (1), determine the output X & Y for the gates shown in…

A: This is a simple question based on digital electronics in which Ex OR , Ex NOR gates are given . We…

Q: Shown in the figure is timing diagram of a T-FF. Using the timing diagram determine which type of…

A: Consider the given question;

Q: Problem #3: board has three clocks that can be seen in the table below: Table 3-2 Pin Assignment of…

A: Let the input clock signal is 10MHz, ADC_CLK_10 clock signal. Which is provided to the LPM counter.…

Q: With the aid of diagrams, discuss the procedure to detect zero error and cyclic error in fieldwork.

A: Field work- Field work is typically work that is not done in the main office buy at the customers…

Q: The 555 timer is mounted and connected to the power and ground terminals of the IC. The circuit…

A: The given circuit diagram is of Astable multivibrator using IC 555.   Requirement is R1 > 1kΩ R1…

Q: S We measured the current that appeared on the plotted screen as shown in the figure by means of…

A: The most popular form is the D'Arsonval galvanometer, which uses a light coil of wire strung from a…

Q: In the figure below Power Processor Stop/Start a. Select one: Input Output O C. O d. Motor O e. b.…

A: The given figure is shown below.

Q: The circuit in Figure Q4 (c) consists of edge triggered flipflops. The second flipflop receives the…

A: Give the circuit: 1. We need to define clock skew. 2. We need to explain with a timing diagram,…

Q: b) Match the name of each component with its respective symbol. Choose five (5) symbols and explain…

A: Symbols are used in drawing of circuit.

Q: 6. Complete the timing diagram for the shown inputs sequences in Figure 14. 00111001 A Dax X…

A: Given data, Logic circuit is, Inputs are, A 0 0 1 1 1 0 0 1 B 1 0 1 0 0 1 0 0

Q: 19. Identify the response time of a meter. a. Time taken by output to reach final constant value…

A: Identify the response time of a meter. It's depend on the parameter.

Q: Suppose we have an illustration: Allen-Bradley SLC 500 PLC connected to two process switches as…

A: According to the question, for the given PLC connections as shown belowWe need to determine the bit…

Q: 4a. b. C. A 555 timer in astable mode is used to provide a clock signal for a stopwatch. The…

A:

Q: Find the Vo during the positive half cycle of the Circuit below Find the Vo during the negative half…

A: In the question, Find the Vo during the positive half cycle of the Circuit below Find the Vo during…

Q: he difference between the measured values obtained when the quantity is increasing and when…

A: error is difference between the actual value and the value indicated by the instrument

Q: Complete the timing diagram for the following circuit (Qo, Q₁start as zero).

A: The timing diagram for the given sequential circuit needs to be obtained and the same can be…

Q: 8. The standard measurement data table of a thermocouple is developed when the thermocouple's…

A: thermocouple circuit with one end in an ice bath (0°C) and the other in an unknown temperature. This…

Q: Remember to put no space in between characters. If the final answer is a whole number, put no…

A: Note: As per our policy, I have answered the first three subquestions. Given data: C1=2.5 FC2=1.5…

Q: Fill in the blanks: Given the model for position control system, find the value for K1 and K2 so…

A: Given, Position control system is Peak time,tp = 0.5s %overshoot = 3% We need to determine values…

Q: Match the given functions with the components of a wind turbine. Converts the mechanical energy to…

A: Yes turbine convert the mechanical power into electrical power.

Q: A) Write Verilog code describing the following circuits in A and B. Clocko DO E LL DOC E O Q B) DODI

A:

Q: Identify the signal processor from the below following.

A: A thermistor (or thermal resistor) is defined as a type of resistor whose electrical resistance…

Q: clock pulse every second. It is directly

A: The decimal counter is a counter which has ten states. It changes its state after every clock…

Q: Draw the pin diagram of 8051 & 8237 and write down the difference between them.

A: The pin diagram of 8237 pin is given below; The pin diagram of 8051 pin is given below;

Latches and Flip Flop

Just like logic gates, the latches and flip-flops are the important elements of an electronic circuit. The logic gates form the important part of combinatorial circuits, while the latches and flip-flops form the essential part of a sequential circuit. Sequential circuits form the important concept of automata theory in electronics and electrical engineering, these circuits are a kind of logic circuit whose output depends on both present input and past inputs, that is, the input history.