Question 1 Determine the pulse duration of a periodic pulse train whose duty cycle is 15% and period is 120 nanoseconds. а) b) Draw the truth table for the following combinational logic circuit. A B C c) Create the gray code representation of the following binary numbers. i) 11101ii) 01101 iii) 10111 iv) 00110 v) 01100

Question 1 Determine the pulse duration of a periodic pulse train whose duty cycle is 15% and period is 120 nanoseconds. а) b) Draw the truth table for the following combinational logic circuit. A B C c) Create the gray code representation of the following binary numbers. i) 11101ii) 01101 iii) 10111 iv) 00110 v) 01100

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Design the following combinational logic circuit with a four-bit input and a three-bit output. The input represents two unsigned 2-bit numbers: A1 A0 and B1 B0. The output C2 C1.C0 is the result of the integer binary division A1 A0/B1 B0 rounded down to three bits. The 3-bit output has a 2-bit unsigned whole part C2 C1 and a fraction part CO. The weight of the fraction bit CO is 21. Note the quotient should be rounded down, i.e. the division 01/11 should give the outputs 00.0 (1/3 rounded down to 0) not 00.1 (1/3 rounded up to 0.5). A result of infinity should be represented as 11.1. A minimal logic implementation is not required. (Hint: start by producing a truth table of your design).
Using logic gates, draw a logic circuit for adding and subtracting numbers (numbers converted to formula 01) where the input is by switches and the output is connected to Segment ships to display the result of the addition and subtraction process, the circuit is 4 bits.
13)In a ladder logic program, one should never A)use the name of a coil for a contact B)use a coil with a designation other than %Q C)use the same coil as an output on more than one rung D)use the same contact on more than one rung
This question is from the subject Digital Logic Design. Assume your register number FA19BSExxx (excluding the dashes -) is in Hexadecimal, where xxx are the three digits of your registration number. a) Represent your registration number in the binary. b) Split the ten digits of your registration into two Hexadecimal numbers M and N, where the left most five digits make number M and the right most five digits make number N. Using r’s complement, subtract N from M. In other words, calculate M – N. Solve the question for registration no SP20-BCS-156.
Logic
Solve the following question. You must show your work. a) What does 962F000016 represent in an IEEE single-precision floating-point number? b) Convert -151o to a 16-bit sign-magnitude representation. c) Convert-151o to a 16-bit two's complement representation. d) Define the system status register value after an instruction execution resulted the following: a. Result was a non-zero value, a negative value, had a carry and extended bits. b. Trace mode was not on and was executed in supervisor mode. C. Any higher interrupt priorities higher than level 3 will be recognized.
My Id number is 200206931 Please answer this quick
I need the answer as soon as possible
a) 13–9 b) –13 –13 Perform the above decimal arithmetic problems by first converting the numbers to binary, 2’s complement form (using a 7 bit word in every case). Then perform the 2’s compliment addition. Show the result in binary indicating as in the problem above whether each result is positive or negative or overflowed (by writing “positive”, “negative” or “overflow” next to the binary answer) and then follow with the decimal value of the result if there was no overflow.
Which logic circuit consisting of two inputs single output logic gates performs the following operation in the simplest way?
Please fa