Question 1 Determine the axial force in the members FH, FE, EH and HG and indicate whether the memebrs are in tension or compression. 350 lb 250 lb 4 in 4 in B 4 in 6 in 6 in + 6 in-| 6 in

Q: Determine the force in member CF in lbs.  If P1 = 638 lbs and P2 = 842 lbs note: Negative value if…

A: To find force in member CF

Q: The internal force in member AB is most nearly. 500 lb B 500 lb ↓ 4 ft 2 ft T -5-10 2 ft $ PD

A:

Q: AC, FD, BE, and CD are rigid members. Determine the internal force in member BE and CD. Select the…

A:

Q: For the frame shown below, Member BC is in -1.2 m D 0.1 m 0.3 m

A: The block is  trying to move downward side.

Q: A compound steel (E = 30,000 ksi) bar is subjected to the loads shown. Bar (1) has a cross-sectional…

A:

Q: A 14 ft long W12 x 65 beam-column is part of a braced frame and supports service loads of Pp = 180 k…

A: W12x65 , Ag = 19.1 in2, Ix = 533 in4  , Lp = 11.9 ft   and Lr = 35.1 ftLb = 14 ft  , Cb = 1.0 Kx =…

Q: Q5) Determine the force in members JK, JN, and CD. State if the members are in tension or…

A:

Q: Q1: For flexural strength only, design the beam shown in the figure (1). The beam has three lateral…

A:

Q: HW03-02 Note that all internal angles on the truss are 60 degrees. Analyze by Method of Joints. Also…

A:

Q: Assume that all members are pin connected and P = 5 kN. (Figure 1) Figure 3 m3 m3 m3 m- P FEP =…

A: A truss is hinged at E and a roller is supported at A.3  point loads are acting downward of P = 5kN…

Q: 900 lb 600 lb 4 ft 4 ft 3 ft A,

A:

Q: using method of joints, please help me calculate all the force of all the members. thanks!

A:

Q: Determine the force in members BC, CF, and FE. State if the members are in tension or compression.…

A: Question is based on truss supported on hinge supports. Load on joints and length of member is given…

Q: Question 3 Please determine the number of Degree of Freedoms (DOFs) of the structures in below when…

A: Degree of freedom is defined as minimum numbers of independent variables required to define the…

Q: The support at G is a pin and the support at A is a roller. Determine the force in members KJ, CJ,…

A: Firstly we will find the components of inclined load into vertical and horizontal loads as shown in…

Q: 4.5) The live load deflection d, is A) 1.331 in B) 1.112 in C) 0.620 in D) 0.434 in

A:

Q: Determine the force in each 500 Ib member of the truss via the method of 1000 lb 2.5 fi joints and…

A:

Q: 4.4) The design shear strength D,V, is A) 81.1 kips B) 482 kips C) 529 kips D) 567 kips

A:

Q: 3. Design a column of wide flange section W for the member (DE) of the frame shown below The frame…

A: Given data: Axial load on the column, P=2500 kN Effective length factor, Ky=1.0 and Kx=2 The column…

Q: B Steel E = 29 x 10 psi 7 = 490 lb* in. 4ft D Aluminura E = 10.1 x 10 psi 7 = 170 ³ Determine (a)…

A: For steel strut: E=29×106  psiγ=490 lb/ft3L=4 ft 12 in1 ft=4×12 ind=12 in=0.5 in For aluminium…

Q: A member in a braced frame supports an axial compressive load and end moments that causes bending…

A: Point load, Length of the member, L = 16'Moment at top,Moment at bottom,Kx=ky=1Assume A992 steel,…

Q: 3) Rigid bar ABC is supported by pin-connected bar (1). Bar (1) is 2.0-in. wide, 1.00-in. thick, and…

A:

Beams

In structural engineering, a beam is a component made of a variety of materials (including steel alloys, and wood) that can resist loads applied laterally to the beam axis. Members, elements, rafters, shafts, and purlins are all terms used to describe beams.