Question 1A very common form of latch circuit is the simple "start-stop" relay circuit used for motor controls,whereby a pair of momentary-contact pushbutton switches control the operation of an electric motor. Inthis particular case, I show a low-voltage control circuit and a 3-phase, higher voltage motor:lllllllllTo 3-phasepower sourceF1F2L1StartStopM1M1M1motorExplain the operation of this circuit, from the time the "Start" switch is actuated to the time the "Stop"switch is actuated. The normally-open M1 contact shown in the low-voltage control circuit is commonlycalled a seal-in contact. Explain what this contact does, and why it might be called a "seal-in" contact.

In control circuit ( Left diagram). When the push button start, the current from L1 going to stop…

Answered: Question 1 A very common form of latch…

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Assume all of the timers are set for a 3 second delay. When the start button is pressed, nothing happens. None of the motors start. Which of the following could NOT cause this problem. a Overload contact OL1 is open b 1CR relay coil is open c 2CR relay coil is open d The stop button is open
Complete the wiring diagrams as per Worksheets 5-A and 5-B then solve for "A" through "G" for the DC motor on Worksheets 5-A and 5-B when it is running at capacity and its specifications are as follows:Rated input = 125 volts, 16 ampsArmature Resistance = 0.3 ohms(Ω)Shunt Field Resistance = 50 ohms (Ω)Series Field Resistance = 0.6 ohm (Ω)Rheostat Resistance = 12.5 ohm (Ω)A) Voltage drop of armature (IR-arm)a) 4.05 V b) 120.95 V c) 125 V d) 129.5 VB) Voltage generated by motor (E-cemf)a) 4.05 V b) 120.95 V c) 125 V d) 129.5 VC) power consumed by shynt field(p-shunt)a) 54.68 W, b) 312.5 W, c) 1632.83 W, d) 2000 WD) power consumend by armature resistance( P-arm)a) 54.68 W , b) 312.5 W, c) 1632.83 W , d) 3000 W
in figure 43-11 when the start button is pushed and the motorstarts in the forward direction, the plugging switch closes. What prevents the reversing contactor from energizing when the plugging switch closes
Direct current is used in which of the following applications in the industry? Select one: A. ELECTRONIC CONTROL COMPONENTS B. MAGNETIC STARTERS C. THREE-PHASE MOTORS D. NONE OF THE ABOVE
Q2) This PLC is being used to start and stop an electric motor, and also to shut it down automatically if any of three "shutdown" conditions occur: Excessive vibration Overcurrent (overload heater contact) • High winding temperature Power supply Digital inputs Digital outputs Processor To motor contactor YO 120 VAC Start l Stop Oo va OL1 X4 OL2N Gnd Com Com Vibration contact Temperațure contact Overload contact The status of each shutdown contact is as follows: Vibration contact: closed when okay, opens when vibration becomes excessive Overload contact: closed when okay, opens when overloaded Temperature contact: open when okay, closes when hot Draw a PLC ladder-logic program to start and stop this motor.
You’re powering up a new motor in a brushless motor control system. After moving the shaft of the motor lightly left to right, the motor reverses direction and runs away. What’s the problem? A. Power transistor failureB. Wrong motor typeC. Reversed tachometerD. Reversed hall-effect sensor
Please help with answering this question, please write clearly, thanks. If the motor is operating at full load and if its variable resistance Radj is adjusted to 250 ohms, what is the new speed of the motor?(assume no armature reaction).
There is something wrong in this motor control circuit. When the start button is pressed, the contactor energizes but the motor itself does not run: Fuse Fuse Fuse 1 2 3 Contactor 1 2 ...To control circuit Schematic diagram Fuses 1 2 3 ли 12 3 Motor motor 3 2 1 Shaft Identify a good place to check with your multimeter to diagnose the nature of the fault, and explain your reasoning
A 150 HP, 3-phase, 6 pole, 460 V, 60 Hz induction motor draws 195 A line current at full load speed of 1170 rpm and 0.85 pf. Solve for the percent slip at full load. (a). 2.5% (b). 3.0% (c). 2.8% (d). 2.0%
What would be the ground fault/ short circuit protection using an inverse time circuit breaker for 240 volt 5 hp motor with 75 temperature? a. 40amps b. 50 amps c. 60 amps d. 70 amps
D is the correct option explain properly please
A direct current motor is connected to a 250-volt DC supply. The armature has a current draw of 165 amperes when operating at full load. You have been assigned the task of connecting two resistors in the armature circuit to provide speed control for the motor. When both resistors are connected in the circuit, the armature current is to be limited to 50% of the full-load current draw. When only one resistor is connected in the circuit, the armature current is to be limited to 85% of full-load current. Determine the ohmic value and min-imum power rating of each resistor.

SEE MORE QUESTIONS

Recommended textbooks for you

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Fundamentals of Electric Circuits

Electrical Engineering

ISBN:

9780078028229

Author:

Charles K Alexander, Matthew Sadiku

Publisher:

McGraw-Hill Education

Electric Circuits. (11th Edition)

Electrical Engineering

ISBN:

9780134746968

Author:

James W. Nilsson, Susan Riedel

Publisher:

PEARSON

Engineering Electromagnetics

Electrical Engineering

ISBN:

9780078028151

Author:

Hayt, William H. (william Hart), Jr, BUCK, John A.

Publisher:

Mcgraw-hill Education,

SEE MORE TEXTBOOKS