Question 1 a) Plastic section moduli for an I' section. Determine the plastic section moduli about the y-y and z-z axes for the I' section shown in Figure below. The section is for a 914×419×388 kg Universal Beam with the root radius omitted. b, = 420,5 A4/2 A2 +ty = 21,5 Az y A, Y3 = tW4 Ag/2 zi h = 920,5 →|+ 4 = 36,6

Question 1 a) Plastic section moduli for an I' section. Determine the plastic section moduli about the y-y and z-z axes for the I' section shown in Figure below. The section is for a 914×419×388 kg Universal Beam with the root radius omitted. b, = 420,5 A4/2 A2 +ty = 21,5 Az y A, Y3 = tW4 Ag/2 zi h = 920,5 →|+ 4 = 36,6

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

i need the answer quickly
The last two digits of my redID is 89 for the problem
22:39 The beam is constructed using 2 boards and 3 rows of nails spaced equally. A shear force is applied to the board. d3 d3 Variable Values for the figure are given in the following table. Note the figure may not be to scale. d₁ d₂ d3 d4 d₁ V Value 0.2 m 0.2 m wamap.org 0.08 m 0.5 m 630 N a. Determine the Qat where the boards meet. b. Determine the moment of inertia, I. c. Determine the shear flow for each nail, q. d. Determine the shear force resisted by each nail, F. Round your final answers to 3 significant digits/figures. Q = 0.07 xm³
Consider the truss structure in the figure below. All diagonal members have axial stiffness EA, while the chord members have axial stiffness of 2EA. Using unit load method, find the vertical deflection at joint B. Feel free to use a spreadsheet to help with the tedious calculations, but please be sure the calculation steps are well set out.
3) Considering a three - beam loaded by a P concentrated load P at the mid – span, prove that the deflection at the middle of the beam when three beams are bonded together is 9 (nine) times less than the deflection when they are unbonded. Deflection at the middle of a simply supported beam is A= PL3 PP48EI* The L beams are constructed of the same material.
The following are the properties of a steel section to be used for a beam section:Fy = 248 MPa Area = 21300Ix = 300000000 Iy = 98800000Sx = 2080000 Sy = 746000d = 289 tw = 19.2tf= 31.8 bf = 265w beam in kN/m = 9laterally unsupported length, Lb = 3 m 1. What is the minimum unsupported length of the beam to be considered long? a. 16.2 m b. 14.5 m c. 13.6 m d. 12.8 m 2. What is the critical depth over thickness ratio set by NSCP? a. 206.68 b. 126.68 c. 106.68 d. 16.68 3. What is the allowable bending stress in the given beam section? a. 148.8 b. 163.68 c. 142.68 d. 124.68 4. If the laterally unsupported length been 10 m, what is the allowable bending stress as per NSCP 2001? a. 148.8 b. 163.68 c. 142.68 d. 124.68
05. Consider the deformable pin-jointed truss with loading, geometry and section properties as shown in the Figure Q5. Given that E=2x10"N/m, A=10mm, L=Im and P-lkN. The horizontal displacement of Joint C (in mm, up to one decimal place) is „JointC P 2AE 7. AE AE Figure 05
Find FBC, FBD, FDE, FAB, FBE, FEA, and FCD Show the complete calculation
Need asap
From the figure shown, a truss is subjected to loads PI = 15 kN, P2 = 15 kN and P3 = 25 kN at joint C, D and E respectively. Use SI = 3 m; S2 = 4 m P₁ Properties of diagonal members (2L75 x 75 x 6): Ag = 1858 mm2 Fy = 248 MPa rx = 22.9 mm ry = 33.2 mm G a) What is the axial force in kN, in member DI? b) What is the allowable stress in MPa, in member DI? c) Calculate the allowable load in kN, in member DI. H 6 @ Si I P₁ E B S, CIVIL ENGINEERING- STEEL DESIGN ...
Two simply supported beam A and B are under same udl Loading. The span of A is double of span B. The correct statement is 1. 2₁ 3. 4. Deflection of A = 2x Deflection of B Deflection of A 4 x Deflection of B Deflection of A = 8 x Deflection of B Deflection of A =16 × Deflection of B
A simply supported girder spans 10 m. It carries two beams each at 3.5 m from the supports. The concentrated load from each beam is 70 kN