I need the answer as soon as possible Question 11. Discuss the working principle of a linear variable differential transformer.2. An LVDT has the following data: Vin = 6.3 V, Vout =+/- 5.2 v, displacement range = +/-0.5 in. Calculate the displacement when Vout = +2.6 V.Question 21. Namethe metal combinations of a thermocouple thermometer to measure temperaturesfrom-270 to 1370 °C:)2. When the cold junction of a thermocouple thermometer is at 5°C and the hot junctuon at110 °C, the millivoltmeter shows a deflection of 3.5 mV towards the left. The hotjunction is now put in an unknown temperature while maintaining the cold junction at5°C. The millivoltmeter now shows a deflection of 4.7 mV towards the left. Calculate theunknown temperature.

Question 1 : 1) Linear variable differential transformer : LVDT is an electromechanical device…

Answered: Question 1 1. Discuss the working…

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

What 10 Wireless Equipment items need to purchase for a daycare business building?
15. _______ is a proximity sensor that uses the principle of ‘eddy current’ to sense the presence of an object.
Untitled form Your email address will be recorded when you submit this form. Not eng.refcon.k2324@sadiq.edu.iq? Switch account objective question(jW Jlgs) For the circuit shown below choose the correct answer V2 Vi SA 220 300 25A In 31
What is the lighting and receptacle demand load for an 1000 sq. m office space with one hundred ten, 15 A, 250 V receptacles. [Office General Lighting Receptacle]
1)The NEC Style Manual indicates that if a term in the NEC appears in more than two articles, it qualifies for a definition in which of the following. a) The articles where the term appears b) Article 90 c) Article 100 d) Table of Contents 2)Definitions of terms related to grounding and bonding and used only in Article 250 are located in ________.a) Article 100 b) Article 200 c) Chapter 9 d) Section 250.2 3)As a general rule, when installing ground rod electrodes, two must be installed always unless a single ground rod provides not more than 25 ohms’ resistance to ground. a) True b) False
i need the answer quickly
Refer to the National Electrical Code® or the working drawings when necessary. Where applicable, responses should be written in complete sentences. For problems 1 and 2, six luminaires, similar to Style E used in the Commercial Building, are to be installed in a room that is 12 ft x 18 ft (~3.7 m x ~5.5 m) with a 9 ft (2.8 m) floor-to-ceiling height. The spacing ratio for the luminaire is 1:0. 1. The maximum distance that the luminaires can be separated and achieve uniform illuminance is ft ( m). For problems 2-5, two luminaires, 8 ft (2.5 m) and 4 ft (1.2 m) in length with dimensions as shown in Figure 15-7, are to be installed in tandem (end to end). The end of the long luminaire is to be 2 ft (600 mm) from the wall. 2. The center of the outlet box should be roughed in at ft ( m) from the wall. 3. The first support should be installed at the wall. ft ( m) from 4. The second support should be installed at from the wall. ft ( m) 5. The final support should be installed at the wall. ft…
Can I use a distribution box on every floor to distribute telephone lines to their designated outlets?
QUESTION 3 We are running 3 wires and a ground in a RMC to a control panel with a 60 amp circuit breaker disconnect in the control panel. The conduit is run along the ceiling where the ambient air temperature is 100 degrees. The control panel feeds our secondary cooling pump. What size are the ungrounded conductors? All conductors have typeTHHN insulation.
Hey see
The only way to reach any of the levels where ABC Company is located in a building with ten stories is to use the elevator. In addition, those on the ninth and tenth levels need to connect to a group of servers located on the eighth. Describe the best wiring for the lift shaft. Pick the best option if there is more than one and justify your decision. If you think that interfloor connections may need to operate at substantially greater rates in the future, you may want to reconsider your current option. What is the optimum media for unbounded data transfer requirements? Justify your response.
Please answer in typing format

Recommended textbooks for you

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Fundamentals of Electric Circuits

Electrical Engineering

ISBN:

9780078028229

Author:

Charles K Alexander, Matthew Sadiku

Publisher:

McGraw-Hill Education

Electric Circuits. (11th Edition)

Electrical Engineering

ISBN:

9780134746968

Author:

James W. Nilsson, Susan Riedel

Publisher:

PEARSON

Engineering Electromagnetics

Electrical Engineering

ISBN:

9780078028151

Author:

Hayt, William H. (william Hart), Jr, BUCK, John A.

Publisher:

Mcgraw-hill Education,

SEE MORE TEXTBOOKS

Question 1 1. Discuss the working principle of a linear variable differential transformer. 2. An LVDT has the following data: Vin = 6.3 V, Vout =+/- 5.2 V, displacement range = 0.5 in. Calculate the displacement when Vout = +2.6 V. +/-