Quest 1: Calculate the moment of the force P about the axis AD using (a) point A as the moment center (b) point D as the moment center 6 ft P= 240 lb 211 51 81 PEDMI NOTE 5 RRO

Q: The plan of a map was photo copied to a reduced size such that a line originally 100 mm, measures 90…

A: Original size = 100 mm Reduced size = 90 mm Original scale = 1:1000   The revised scale is =?

Q: is the answer 11532?

A:

Q: Define PDOP?

A: PDOP ( Position dilution of precision) It describes the error caused by the relative position of the…

Q: Draw a sample topographic map that shows hachures.

A: A topographic map shows the details about elevation of natural and man made features of that area.…

Q: site map

A: Land surveying allows us to understand land boundaries.A survey is performed in order to locate,…

Q: Define earth work

A: The engineering work that is created by moving and/or processing unformed rock or large amounts of…

Q: In detail what is the CSI MasterFormat and what is listed in division 28?

A: Answer  CSI MasterFormat also known as "Dewey Decimal system" is the product of the Construction…

Q: Differentiate between BIM and 3DModeling?

A:

Q: Revit Properties Box is used for what?

A: In the field of civil engineering or architecture, Revit is used to create the structural model that…

Q: Write the units used by English systems to specify small areas?

A: Solution: In the English system, areas are basically given in square feet or square yards. For…

Q: What is the Global Coordinate System (GCS)? Why was the Viewing Coordinate System created?

A: Global Coordinate system is a coordinate system in which we are enabled to make a location details…

Q: How would you characterise GIS?

A: GIS (Geographic Information System) is a computer-based tool used for collecting, storing,…

Q: Plot the contour lines using the given set of elevations and contour interval. Use the simplest…

A: contour interval is the elevation difference represented on map between two consecutive contour…

Q: List the different meridians are used to specify directions?

A: The direction of a survey line can be defined in two ways: Relative to each other  Relative to some…

Q: Topographic ORIENTATION: -Magnetic and Geographic North -Azimuth and bearing -Magnetic…

A: Surveying: Identifying the geographical or three-dimensional locations of objects, as well as the…

Q: Which of the following are common software for Design / Constructability Review? AutoCAD or…

A:

Q: Prompts A drawing that shows an accurate layout of a piece of land. 2 A drawing that shows an…

A: Gievn data,5 statement is given and choose the correct option for each statementLet's choosing the…

Q: Explain the Eurocode terminology : GEO

A: GEO The application of scientific methods and engineering techniques and utilization of natural…

Q: What is the most important thing to ensure when it comes to layouting?

A: Civil surveying is a type of engineering that includes analysing and documenting information about a…

Q: 1.13 List the legal requirements for registration as a land surveyor in your state. 1.14 Briefly…

A: There are different eligibility criteria to become a land surveyor. One should need to fulfill all…

Q: Give the vector in cartesian coordinates that extends from B(4, 20degrees, 10degrees) to W(7,…

A: The given data is shown below: B=4,20 degrees, 10 degreesW=7,120 degrees, 75 degrees

Q: a. On the equator: b. Golden, Colorado: C. Barrow, Alaska: 0° latitude 39°44'N latitude, 105°12'W…

A:

Q: How to create stacked bar chart in tableau

A: This question is related to the Computer-aided design software from Civil Engineering. This is…

Q: What is National Spatial Reference System?

A: National Spatial Reference System  (NSRS) A consistent coordinate system that defines latitude,…

Q: Define Spencer Charts.

A: Spencer defines the factor of safety as the available shear strength quotient divided by mobilized…

Q: How many divisions are on the vernier scale?

A: A vernier scale is a visual representation that uses mechanical approximations to obtain an exact…

Q: With the aid of an illustration, describe two methods by which areas bounded by irregular lines can…

A: Areas bounded  by irregular lines can be found by using midoridnate rule , trapezoidal method ,…

Q: Map scale is identified as a ratio between Select one: O a. ground distance to map distance O b. map…

A: Given data : The value of distance on map=DM The value distance on ground=DG   Required : Map scale

Q: re there any situations where a scale layer can be helpful to a water utility? (answer in one or two…

A: calcium carbonate form the protective layer on lead pipe by making lead carbonate. which increase…

Q: GIS is an abbreviation for Geographic Information System.

A: what is GIS? Geographic information system is a computer based information system design to accept…

Q: ow is the text size for dimensions and text managed in Revit? Setting the dimension style to the…

A: This question is related to AUTOCAD from Civil Engineering .

Q: Kindly clarify what you mean when you refer to "GIS."

A: GIS stands for Geographic Information System. GIS are used for capturing all data that are required…

Q: Prioritize the following line types. If a line type is prioritized, that means that it will be…

A: Object lines, center lines and hidden lines are various types of lines used in construction…

Q: Figure below represent contour lines for ground surface and wells located on it 50 w2 W1 fill table…

A: given-water table elevation of wells-W1=60W2=50W3=40

Q: Pasig River EXISTING STRUCTURE EXISTING STRUCTURE PSG COMPOUND Croek Creek 2 SITE DEVELOPMENT PLAN…

A: Plan detail of  a site is given. From the given detail various important factors which comes out…

Q: .Find scale and units of map 2.Find DATUM & UTM

A: From the given question it is required to Find scale and units of map. Find DATUM & UTM.

Q: Give an introduction to Hydrographic Surveying/Hydrography and specifically, the chosen field of…

A: With a focus on providing information for safe navigation, resource management, and environmental…

Q: What are velocity charts?

A: The Velocity Chart displays the value amount delivered in each sprint so as to forecast the work…

Q: The Global Coordinate System (GCS) is an acronym for Global Coordinate System. What motivated the…

A: Global Coordinate System is an absolute reference system which is used to define locations of nodes…