QUE3 mON 5 A cylindrical pressure vessel has an inner diameter of1.2 m and a thickness of 12 mm. Determine the maximum internal pressure it can sustain so a that neither its circumferential nor its longitudinal stress component exceeds 140 MPa. Under the same conditions, what is the maximum internal pressure that a similar-sized spherical vessel can sustain? C. Under the same conditions, what is the maximum internal pressure (MPa) that a similar-sized spherical vessel can sustain?

QUE3 mON 5 A cylindrical pressure vessel has an inner diameter of1.2 m and a thickness of 12 mm. Determine the maximum internal pressure it can sustain so a that neither its circumferential nor its longitudinal stress component exceeds 140 MPa. Under the same conditions, what is the maximum internal pressure that a similar-sized spherical vessel can sustain? C. Under the same conditions, what is the maximum internal pressure (MPa) that a similar-sized spherical vessel can sustain?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A cylindrical tank having a pressure of 114.0 kPa is used to carry a 3.5 m3of water has a height of 2.0 m and thickness of 5.0 mm. Determine the following What is the diameter of the tank The tangential and longitudinal stress in the tank
i li. In. O MMecnaniCS / مطلوب Untitled Section F1 F2 a F3 B. d F4 F5 Consider the following values: - a - 25 m; b - 5 m; a - 25 m; d - 5 m; F1 = 6 KN; F2 = 7 kN; F3 = 8 KN; F4 = 9 kN; F5 = 10 KN; a = 60°, 0 = 45°, B== 30° 1] What is the resultant moment of the five forces acting on the rod about point A? a) - 15.8 kN.m b) 74 kN.m c) 88 kN.m d) 59 kN.m e) 241 kN.m 0- 47 kN.m 2] What is the resultant moment of the five forces acting on the rod about point B? a) 218.8 kN.m b) – 117.8 kN.m c) - 131.6 kN.m d) 98.9 kN.m e) 125.4 kN.m f) - 224.2 kN.m 3] What is the resultant moment of the five forces acting on the rod about point C? a) 186.7 kN.m b) - 143.6 kN.m c) 114.6 kN.m d) - 217.9 kN.m e) 224.1 KN.m ) - 135.3 KN.m 4] What is the resultant moment of the five forces acting on the rod about point D? a) 217.8 kN.m b) – 139.5 kN.m c) 111.9 kN.m d) 206.9 kN.m e) - 127.1 kN.m f) 99.1 kN.m Activate 5] What is the moment of the force F2 about point E? Go to Setting f) 321.3 kN.m a) 121.7 kN.m…
A vertical cylindrical steel tank 3 m in diameter and 6 m high has a wall thickness of 12 mm. If the stress is limited to 5 MPa, which of the following most nearly gives the maximum height of water up to which the tank may be filled? Select the correct response: 8.16 m 3.68 m 07.36 m 4.08 m
Read the question carefully and give me right solution according to the question.
A hydraulic system is used to apply a force in an external fixation device to hold brokenends. The piston of this hydraulic ram is 30 cm in diameter and the water pressure is 3 MN/?2 Determine The stress in the piston rod which has dimeter of 4 cm
A thick cylinder of 0.5 m external diameter and 0.4 m internal diameter is subjected simultaneously to internal and external pressures. If the internal pressure is 25 MN/m2 and the hoop stress at the inside of the cylinder is 45 MN/m2 (tensile), determine the intensity of the external pressure,
A cylindrical pressure vessel is fabricated from steel plating that has wall a thickness of 10 mm and is subjected to an internal pressure of 2.5 MРа. Calculate its outer diameter if the longitudinal stress is limited to 95 N/mm2.
How did it end up with a unit of kilogram?
Q4//Determine the required vertical force F to be applied at the lower edge to open the square gate (2.8m*2.8m) as shown in figure below: Negative pressures 8250Pa 1.8m Gasoline s-0.7 hinge gate
A thick-walled cylinder with closed ends is subjected to internal pressure pi and external pressure po. If a = 0.6m, b = allowable value of p; in terms of o. You can start from cquation (8.8) from the textbook. Im, oall 1000, and Tall = 500 and Po = 300, determine the a²p; – b*po 62 a2 (Pi – Po)a²b? (b² – a²)r² (Pi – Po)a?b? (6? – a²)r2 Or = a?pi – b*po 62 – a? Show the maximum allowable pi due to (a) hoop stress og = 0al; (b) longitudinal stress oz = o all, and (c) maximum shear stresS Tmax = Tall - What is the overall maximum allowable p;?
Gas having an internal pressure of 4 MPa is housed in the 3-meter-high pressure tank below. It experiences a 18 kN external load, as illustrated. Calculate the tank's maximum longitudinal and circumferential stresses (in MPa). The tank has a 30 mm thickness. 175 cm 60cm 18 kN 18 KN
Q2: A spacer is turned from Aluminum alloy with elasticity modulus of 78 GN/m?. The spacer has a diameter of 28 mm and a length of 245 mm. both measurements being made at 20°C. The temperature of the spacer is then increased to 100 °C, the natural expansion being entirely prevented. Taking the coefficient of linear expansion to be 18 x 10-6 °C. Determine the compressive load on the spacer.