Qs) A Single-phase, hp, 230V, 60 HZ, four-jpole, 1710 rpm induction motor has the following parameters: Xz=12.02 and XM 260 At rated speed, the core loss is 3ow and the friction and Windage loss is IS W. The motor is Connected to an io,230v, 60 HZ and runs at the rated speed. Determine : (a).'The-slip- The motor current.. r-9.52, XI-12.02, Yz=10.8, (e) The power factor. The input power. ce): The developed torque. (F) The output shaft power and shaft torgue . (9) The efficiency. (h). The rotor frequencies and the rotor cu- lo sses ti) The ratio of the forward flux to the backward flux (d)

Qs) A Single-phase, hp, 230V, 60 HZ, four-jpole, 1710 rpm induction motor has the following parameters: Xz=12.02 and XM 260 At rated speed, the core loss is 3ow and the friction and Windage loss is IS W. The motor is Connected to an io,230v, 60 HZ and runs at the rated speed. Determine : (a).'The-slip- The motor current.. r-9.52, XI-12.02, Yz=10.8, (e) The power factor. The input power. ce): The developed torque. (F) The output shaft power and shaft torgue . (9) The efficiency. (h). The rotor frequencies and the rotor cu- lo sses ti) The ratio of the forward flux to the backward flux (d)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q5:- Adjust a fire angle for a three-phase fullwave semi-controlled converter to feed the separately exciter DC motor to get a load torque that can be reached to 730 rpm. When the supply voltage of converter is 160 volts per-phase and the absorbed current through the armature 40A with resistance 0.2 and a constant back emf 0.4v/rpm. Then find the maximum speed for motor assume the previous parameters values are a constant.
For a 18600W 2400rpm DC motor, the following values are given: Ra = 0.089 2 (value at room temperature (250C)), La = 0.00144 H, KT = 0.85 Nm / A and KV = 0.851 V / (rad / s)), (In calculations Use the hot resistance values at 1000C.) (Take the rated field winding losses as Wf= 210W.) If this DC machine is operating as a motor with rated flux at rated speed, calculate the rated torque (TR), rated current (IR), rated voltage (VR), efficiency (n) at the rated point, taking into account the winding losses. Find the speed (@NL) of this motor in no-load condition. TR Nm IR А VR V Eff = % ONL= rpm
Q2 Complete the answer : The rotor reactance of the three phase induction motor is varies with ................... of the rotor current.
A three-phase, 460 V, 98hp 1,60 Hz, four-pole induction machine delivers rated output power at a slip of 0.05. Determine: (i) The synchonous speed. (V) speed at half Load (ii) The motor speed. (iii) The rotor frequency. (iv) The slip speed. ...A... -
12. The IR-compensation in frequency control of induction motors is used for: a) compensation of the voltage drop in the active resistance of the stator winding. b) compensation of the voltage drop in the inductive reactance of the stator winding. c) keeping the motor voltage constant. d) keeping the motor speed constant U₁ U₁ Us0 0 f. f₁
A) At what percentage of slip is the pull-out or breakdown torque of a typical 3-phase squirrel- cage induction motor reached? 21. a) 3% slip b) 10% slip c) 20% slip d) none of the above B) If load is increased beyond the breakdown torque, what happens to the speed of the motor? a) it stops b) it may speed up beyond its rated rpm c) its speed will not change, but its current will go down d) none of the above
A three-phase, 460 V, 98hp 1,60 Hz, four-pole induction machine delivers rated output power at a slip of 0.05. Determine: (i) The synchonous speed. (V) speed at half Load (ii) The motor speed. (iii) The rotor frequency. (iv) The slip speed. ...A... -
A 460 V, 60 Hz, Star connected, 870 r.p.m., Eight poles, Three-Phase Induction Motor has the following per phase parameters: R1 = 0.07, R2 = 0.05, X1 = X2 = 0.2, Xm = 6.5, Draw the approximate equivalent circuit and determine the following:I. Starting TorqueII. Maximum TorqueIII. Rated TorqueIV. Stator CurrentV. Power FactorVI. Input PowerVII. Magnetizing Current
Q1) A 3-phase, star-connected ,220V,6-poles,induction motor has the following constants: (R1=0.32),(R2=0.15).(X1%3D0.50).(X2=0.22),(Xm=132) the total Friction losses+ core losses are( 1000W), the slip is (0.02) determine : 1-the efficiency, 2- the output torque