Ql: (a) Using figure below, determine the collector current if Ip= 5 mA and VCB =15 V. Then determine the collector current if Ip remains at 5 mA but VCB is 5 V. (c) Using Figure 1 and 2, determine VBE if Ic = 3 mA and VCB = 10 V. 14 (ma) t'e tmA) -Active region (uasladed area) - Ve= 20 v Va = 10 v VEIV 4 mA 3 mA 2 mA -1 mA 02 04 0.6 10 15 Cutoff region Saturation region 1.

Ql: (a) Using figure below, determine the collector current if Ip= 5 mA and VCB =15 V. Then determine the collector current if Ip remains at 5 mA but VCB is 5 V. (c) Using Figure 1 and 2, determine VBE if Ic = 3 mA and VCB = 10 V. 14 (ma) t'e tmA) -Active region (uasladed area) - Ve= 20 v Va = 10 v VEIV 4 mA 3 mA 2 mA -1 mA 02 04 0.6 10 15 Cutoff region Saturation region 1.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

For the circuit in Figure below, what is Ic3? Assume all transistors are identical. IREF 1 Q5 R1 IREF2 O IE of Q2 O 2 IREF1 O IE of Q1 Vh1 Q6 Q1 03 07 8 Vn2 04 IREF2 R2
Assume R1= R2 =D6002, RL=500, and Vcc = 15V. Assuming D1 and D2 are identical and have same characteristics as Q1 and Q2 base-emitter junctions, if the input voltage is 1Vrms, what will be the output peak voltage? Vcc R1 D1 D2 Q2 R2 R2 -Vcc
Solve the emitter voltage of a voltage-divider bias circuit with Vcc=9V, R1-560k ohms, R2=560k ohms,RC=3.3k ohms, RE-680 ohms, and beta - 100. 0.7V Ⓒ4.7V Ⓒ1.44V ⒸOV
Solve for the required value of RD, in kOhms to achieve a drain current ID=5.51mA. VDD=15.38V RG=1MOhms VGS(off)=-4.17V IDSS=14.37mA VD=10.22V
1- a. For the circuits given below calculate the currents through the zener diode (V5.1V) and the current through the Si-diode. 1k Ohm 1k Ohm -10V 1k Ohm 12V b. The emitter of an NPN type BJT is connected to ground. Its base is connected to a 5V supply with a 10K resistor. Its collector is connected to the same supply with a 6K resistor. Calculate the range of ß such that the transistor is not saturated.
A current-source bias circuit in the figure below has the following values: VDp = 10 V, Vee = -6 V, and Rg = 10,045,170 ohms. To produce a 13 mA drain current and a 7 V drain voltage, determine the value of Rp in ohms. Vpp Rp Rg RE -VEE
In a MOSFET amplifier, the AC input signal is applied at gate terminal and the amplified output is taken at source terminal. common emitter common gate common source common drain
Find the operating region of the MOSFET and Vn when In = 0.2A and R=5 ohm? +1.8 V R o Vp O a. None- off the options O b. Cut-off, Vp = 0.8V O c. Triode, Vp = 0.6V O d. Saturation, Vp = 0.8V
For the JFET with maximum drain current 9mA, drain current 2.5mA at gate to source voltage 4V. Calculate the pinch off Voltage.
3. In a certain n-channel JFET, Ipss= 8 mA and Vp=-4 V. (a) Determine the value of Ves for maximum drain current. (b) Calculate the drain current for VGs=-5 V (c) Calculate the drain current for Ves=-2 V (d) Determine the maximum value of VGs for cut-off condition.
In N-channel E-MOSFET, as the VGS increases positively, the Drain current decreases. True or false
a. A 220 ohms resistor is connected in series with the gate of an SCR using basic circuit in figure. The gate current required to fire the SCR is 10mA.What is the input voltage (Vin) is necessary to switch on the SCR?