QI. for the circuit of flg.,a) Derive the output woltage expression Vo in terns of Ri,R2,Rf,NAIN2.6) Assume Ri =10k, R k, Rf = 90k, V=2U2 =12-t are gien.At whattime the output voltage volts would be 0 Volt'sC) Assume Q1=104, R2= 204, Rf = 2ok andUL=-COSCH),u2=- cos CtJ aregiven. At what time Hae output olt ege would be = Volt ?ifラナwiteNnRIFiniPAVofig. 4

Answered: Image /qna-images/answer/39005dc1-3e8e-4d5e-b4c4-f61981ac36bb.jpg

QI. for the circuit of flg.I, a) Derive the output woltage expression vo in terns of Ri,R2,RfivtI2. b) Assume Ri=10k, R2zk,Rf= 0k, V= t3 ,U2= 2 2-t are giuen. 44 what time the output voltage volt) would be O Vot C) Assume Q1=104, R2= 204, 00-20k and vi-cosct),u2=-cos CtJ are %3D given. At what time Hae output vot ege would be Ub= Volt? if Nn RI マin R2 fig. 4.

QI. for the circuit of flg.I, a) Derive the output woltage expression vo in terns of Ri,R2,RfivtI2. b) Assume Ri=10k, R2zk,Rf= 0k, V= t3 ,U2= 2 2-t are giuen. 44 what time the output voltage volt) would be O Vot C) Assume Q1=104, R2= 204, 00-20k and vi-cosct),u2=-cos CtJ are %3D given. At what time Hae output vot ege would be Ub= Volt? if Nn RI マin R2 fig. 4.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Figure B23 Q24. For the circuit shown in Figure B24a, Ve-15V Rc= 2k2 Rs = 20k2 VBB-3V Figure B24a i) Sketch the DC load line in the Graph B24 ii) Calculate the Q point, if the zero signal base current is 60 µA and a = 0.98. Mark the Q point in load line. Page 5 of 6 LG
i need the answer quickly
In the circuit given in the figure, Rk = 7.34Kohm, R1 = 1487.50Kohm, R2 = 1845.84Kohm, R3 = 1.61Kohm, R4 = 0.54Kohm, R5 = 19.05ohm, Ry = 91.57Kohm, VCC = 10.00V, VTN = 2.85V, Kn = Since it is 2.44(mA/V^2), C1=10.04uF, C2=13.81uF, C3=14.07UF, calculate the lower cutoff frequency of the circuit in Hz. When making your transactions, 2 digits will be taken after the dot. Write your result in Hz according to + 10% margin of error. While writing the answer, values such as spaces (Hz, KHz) etc. should not be written in front of the value and behind it. Only numeric values should be entered. A period (.) should be used as a decimal separator. An example notation is given below. Let the value you find be 1.15K. You should write 1150.00 in the box. Let the value you find be 432.6. You should write 432.63 in the box. If the correct answer is X, values entered in the range of X ± (X*10/100) (including limits) will be accepted. If x=50, it will be accepted as between [45,55]. VCc R1 R3 C3 VO Q1 Ry…
cuicuit designed in winknown isubuenit, va resistance R = 2.8K2 and two identical silicon BITS T1 and 12 with 72 and T2 with forward gains BF = 200. The supply voltage Vcc =-25 volts Vcc=25 volts Sub-circuit JICA T2 IB₁1 IB12 VIR R = 28K2 VIC, 2 GIND IB, 1 and Ic, s designate the base and collector current of T2 vespectively where as the courrents IB,₁2 and IG2 designate the base and the collector currents of T2 respectively. T2 and 12 operate in forward active mode Assume that IB, 1 and IB₁2 are equal · VBE, on = 0.8 molt (Threshold woltage) (a) What is the value of the current IR through vesistance R.? (MA) (b) what is the value of the base vaurrent IB, 1? (MA) (c) what is the value of the collector Ic₁₁? (MA) (d) The evicuit idesigned using Resistance Rand Transistors T₁ and To performs an electronic function to connect to sub circut which function is it?
I want a correct and clear solution
What can you say about AM DSB-FC, AM DSB-SC, and AM SSB? What do they have in common and their difference?
a)circuit diagram with a load ,for the JFET. b)input and output waveform c)equations for the output ( v and i)
8. O0 eneogy signal. Find its value Check whethes the given signal is power signal 3 4)" ; n70 xCn) =
Power electronics